Gas Turbines: Cycle Innovations

Preliminary Experimental Results of Integrated Gasification Fuel Cell Operation Using Hardware Simulation

[+] Author and Article Information
Alberto Traverso

 Thermochemical Power Group, University of Genoa, Via Montallegro 1, 16145, Genova, Italyalberto.traverso@unige.it

David Tucker

 National Energy Technology Laboratory, U.S. Department of Energy, Morgantown, WVdavid.tucker@netl.doe.gov

Comas L. Haynes

 Georgia Tech Center for Innovative Fuel, Cell/Battery Technologies, Georgia Tech Research Institute, Atlanta, GA 30332-0823comas.haynes@gtri.gatech.edu

J. Eng. Gas Turbines Power 134(7), 071701 (May 24, 2012) (10 pages) doi:10.1115/1.4005976 History: Received August 10, 2011; Revised September 27, 2011; Published May 24, 2012; Online May 24, 2012

A newly developed integrated gasification fuel cell (IGFC) hybrid system concept has been tested using the Hybrid Performance (Hyper) project hardware-based simulation facility at the U.S. Department of Energy, National Energy Technology Laboratory. The cathode-loop hardware facility, previously connected to the real-time fuel cell model, was integrated with a real-time model of a gasifier of solid (biomass and fossil) fuel. The fuel cells are operated at the compressor delivery pressure, and they are fueled by an updraft atmospheric gasifier, through the syngas conditioning train for tar removal and syngas compression. The system was brought to steady state; then several perturbations in open loop (variable speed) and closed loop (constant speed) were performed in order to characterize the IGFC behavior. Coupled experiments and computations have shown the feasibility of relatively fast control of the plant as well as a possible mitigation strategy to reduce the thermal stress on the fuel cells as a consequence of load variation and change in gasifier operating conditions. Results also provided an insight into the different features of variable versus constant speed operation of the gas turbine section.

Copyright © 2012 by American Society of Mechanical Engineers
Your Session has timed out. Please sign back in to continue.



Grahic Jump Location
Figure 4

Generic reaction scheme used to model cellulose, hemicellulose, and lignin pyrolysis (blue and black arrows). Red arrows regard char gasification.

Grahic Jump Location
Figure 1

Hyper facility with corresponding virtual components

Grahic Jump Location
Figure 2

Simplified flow diagram for the hybrid performance simulation facility at NETL

Grahic Jump Location
Figure 3

Fluid domain: transient model finite difference scheme

Grahic Jump Location
Figure 7

Fuel cell internal profiles. Node 1, on the left, is fuel and air inlet. Node 20, on the right, is fuel and air outlet (coflow configuration).

Grahic Jump Location
Figure 8

System input perturbations: fuel cell (FC) current and oxidant agent (humid air) to the gasifier

Grahic Jump Location
Figure 9

Gasifier syngas thermal content (before the syngas conditioning unit)

Grahic Jump Location
Figure 10

Gasifier significant temperatures

Grahic Jump Location
Figure 11

Raw syngas composition (top) and zoom in significant fuel gases (bottom)

Grahic Jump Location
Figure 12

Fuel cell main parameters: Nernst voltage, operating fuel cell voltage, utilization factor (Uf)

Grahic Jump Location
Figure 13

Fuel cell temperatures and temperature spatial gradients (along the flow axis)

Grahic Jump Location
Figure 14

Gas turbine flows and pressure

Grahic Jump Location
Figure 15

Gas turbine power and speed

Grahic Jump Location
Figure 16

IGFC cycle temperatures

Grahic Jump Location
Figure 5

Gasifier initial mass flow profile. Height: 0 is bottom, 8 is top.

Grahic Jump Location
Figure 6

Gasifier wall initial temperature flow profile. Height: 0 is bottom, 8 is top. Thickness: 0–0.01 is skin, 0.01–0.0500 is insulation, 0.05–0.25 is refractory.



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In