Research Papers: Nuclear Power

Measurement of Flow Phenomena in a Lower Plenum Model of a Prismatic Gas-Cooled Reactor

[+] Author and Article Information
Hugh M. McIlroy

 Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-2200hugh.mcilroy@inl.gov

Donald M. McEligot1

 University of Arizona, Tucson, AZ 85721; Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3870

Robert J. Pink

 Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-2209robert.pink@inl.gov


On sabbatical leave at University of Limerick.

J. Eng. Gas Turbines Power 132(2), 022901 (Nov 02, 2009) (7 pages) doi:10.1115/1.3078784 History: Received August 12, 2008; Revised August 14, 2008; Published November 02, 2009; Online November 02, 2009

Mean-velocity-field and turbulence data are presented that measure turbulent flow phenomena in an approximately 1:7 scale model of a region of the lower plenum of a typical prismatic gas-cooled reactor similar to a General Atomics gas-turbine-modular helium reactor design. The data were obtained in the Matched-Index-of-Refraction (MIR) Facility at Idaho National Laboratory (INL) and are offered for assessing computational fluid dynamics software. This experiment has been selected as the first standard problem endorsed by the Generation IV International Forum. Results concentrate on the region of the lower plenum near its far reflector wall (away from the outlet duct). The flow in the lower plenum consists of multiple jets injected into a confined cross flow—with obstructions. The model consists of a row of full circular posts along its centerline with half-posts on the two parallel walls to approximate geometry scaled to that expected from the staggered parallel rows of posts in the reactor design. The model is fabricated from clear, fused quartz to match the refractive-index of the working fluid so that optical techniques may be employed for the measurements. The benefit of the MIR technique is that it permits optical measurements to determine flow characteristics in complex passages in and around objects to be obtained without locating intrusive transducers that will disturb the flow field and without distortion of the optical paths. An advantage of the INL system is its large size, leading to improved spatial and temporal resolutions compared with similar facilities at smaller scales. A three-dimensional particle image velocimetry system was used to collect the data. Inlet-jet Reynolds numbers (based on the jet diameter and the time-mean bulk velocity) are approximately 4300 and 12,400. Uncertainty analyses and a discussion of the standard problem are included. The measurements reveal developing, nonuniform, turbulent flow in the inlet jets and complicated flow patterns in the model lower plenum. Data include three-dimensional vector plots, data displays along the coordinate planes (slices), and presentations that describe the component flows at specific regions in the model. Information on inlet conditions is also presented.

Copyright © 2010 by American Society of Mechanical Engineers
Your Session has timed out. Please sign back in to continue.



Grahic Jump Location
Figure 2

Mean vector field for Rejet∼12,400

Grahic Jump Location
Figure 3

Mean streamlines for Rejet∼12,400

Grahic Jump Location
Figure 4

Average Vy at y∼−70 mm (top) and y∼−150 mm (bottom)

Grahic Jump Location
Figure 5

Average Vy at y∼−70 mm (top) and y∼−150 mm (bottom)

Grahic Jump Location
Figure 6

Average Vy in inlet jets for Rejet∼12,400 at y∼11, −10<z<+10 at 2 mm intervals



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In