Research Papers: Gas Turbines: Combustion, Fuels, and Emissions

Implementation Challenges and Solutions for Homogeneous Charge Compression Ignition Combustion in Diesel Engines

[+] Author and Article Information
Usman Asad

Department of Mechanical,
Automotive & Materials Engineering,
University of Windsor,
401 Sunset Avenue,
Windsor, ON N9B 3P4, Canada
e-mail: asadu2@asme.org

Ming Zheng

Department of Mechanical,
Automotive & Materials Engineering,
University of Windsor,
401 Sunset Avenue,
Windsor, ON N9B 3P4, Canada
e-mail: mzheng@uwindsor.ca

David S.-K. Ting

Department of Mechanical,
Automotive & Materials Engineering,
University of Windsor,
401 Sunset Avenue,
Windsor, ON N9B 3P4, Canada
e-mail: dting@uwindsor.ca

Jimi Tjong

Ford Motor Company,
1 Quality Way,
Windsor, ON N9A 6X3, Canada
e-mail: jtjong@ford.com

Contributed by the Combustion and Fuels Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received February 27, 2015; final manuscript received March 3, 2015; published online April 8, 2015. Editor: David Wisler.

J. Eng. Gas Turbines Power 137(10), 101505 (Oct 01, 2015) (10 pages) Paper No: GTP-15-1053; doi: 10.1115/1.4030091 History: Received February 27, 2015; Revised March 03, 2015; Online April 08, 2015

Homogeneous charge compression ignition (HCCI) combustion in diesel engines can provide cleaner operation with ultralow NOx and soot emissions. While HCCI combustion has generated significant attention in the last decade, however, till date, it has seen very limited application in production diesel engines. HCCI combustion is typically characterized by earlier than top-dead-center (pre-TDC) phasing, very high-pressure rise rates, short combustion durations, and minimal control over the timing of the combustion event. To offset the high reactivity of the diesel fuel, large amounts of exhaust gas recirculation (EGR) (30–60%) are usually applied to postpone the initiation of combustion, shift the combustion toward TDC, and alleviate to some extent, the high-pressure rise rates and the reduced energy efficiency. In this work, a detailed analysis of HCCI combustion has been carried out on a high-compression ratio (CR), single-cylinder diesel engine. The effects of intake boost, EGR quantity/temperature, engine speed, injection scheduling, and injection pressure on the operability limits have been empirically determined and correlated with the combustion stability, emissions, and performance metrics. The empirical investigation is extended to assess the suitability of common alternate fuels (n-butanol, gasoline, and ethanol) for HCCI combustion. On the basis of the analysis, the significant challenges affecting the real-world application of HCCI are identified, their effects on the engine performance quantified, and possible solutions to overcome these challenges explored through both theoretical and empirical investigations. This paper intends to provide a comprehensive summary of the implementation issues affecting HCCI combustion in diesel engines.

Copyright © 2015 by ASME
Your Session has timed out. Please sign back in to continue.


Dec, J. E., 2009, “Advanced Compression–Ignition Engines—Understanding the In-Cylinder Processes,” Proc. Combust. Inst., 32(2), pp. 2727–2742. [CrossRef]
Asad, U., Divekar, P., Zheng, M., and Tjong, J., 2013, “Low Temperature Combustion Strategies for Compression Ignition Engines: Operability Limits and Challenges,” SAE Technical Paper No. 2013-01-0283. [CrossRef]
Asad, U., Zheng, M., Han, X., Reader, G. T., and Wang, M., 2008, “Fuel Injection Strategies to Improve Emissions and Efficiency of High Compression Ratio Diesel Engines,” SAE Int. J. Eng., 1(1), pp. 1220–1233. [CrossRef]
Maiboom, A., Tauzia, X., and Hétet, J.-F., 2008, “Experimental Study of Various Effects of Exhaust Gas Recirculation (EGR) on Combustion and Emissions of an Automotive Direct Injection Diesel Engine,” Energy, 33(1), pp. 22–34. [CrossRef]
Kodama, Y., Nishizawa, I., Sugihara, T., Sato, N., Iijima, T., and Yoshida, T., 2007, “Full-Load HCCI Operation With Variable Valve Actuation System in a Heavy-Duty Diesel Engine,” SAE Technical Paper No. 2007-01-0215. [CrossRef]
Zhao, H., Xie, H., and Peng, Z., 2005, “Effect of Recycled Burned Gases on Homogeneous Charge Compression Ignition Combustion,” Combust. Sci. Technol., 177(10), pp. 1863–1882. [CrossRef]
Shi, L., Cui, Y., Deng, K., Peng, H., and Chen, Y., 2006, “Study of Low Emission Homogeneous Charge Compression Ignition (HCCI) Engine Using Combined Internal and External Exhaust Gas Recirculation (EGR),” Energy, 31(14), pp. 2665–2676. [CrossRef]
Asad, U., and Zheng, M., 2009, “Efficacy of EGR and Boost in Single-Injection Enabled Low Temperature Combustion,” SAE Int. J. Eng., 2(1), pp. 1085–1097. [CrossRef]
Kimura, S., Ogawa, H., Matsui, Y., and Enomoto, Y., 2002, “An Experimental Analysis of Low-Temperature and Premixed Combustion for Simultaneous Reduction of NOx and Particulate Emissions in Direct Injection Diesel Engines,” Int. J. Eng. Res., 3(4), pp. 249–259. [CrossRef]
Akihama, K., Takatori, Y., Inagaki, K., Sasaki, S., and Dean, A., 2001, “Mechanism of the Smokeless Rich Diesel Combustion by Reducing Temperature,” SAE Technical Paper No. 2001-01-0655. [CrossRef]
Kokjohn, S., Hanson, R., Splitter, D., and Reitz, R., 2011, “Fuel Reactivity Controlled Compression Ignition (RCCI): A Pathway to Controlled High-Efficiency Clean Combustion,” Int. J. Eng. Res., 12(3), pp. 209–226. [CrossRef]
Lu, X., Han, D., and Huang, H., 2011, “Fuel Design and Management for the Control of Advanced Compression–Ignition Combustion Modes,” Prog. Energy Combust. Sci., 37(6), pp. 741–783. [CrossRef]
Gao, T., Divekar, P., Asad, U., Han, X., Reader, G. T., Wang, M., and Zheng, M., 2013, “An Enabling Study of Low Temperature Combustion With Ethanol in a Diesel Engine,” ASME J. Energy Resour. Technol., 135(4), p. 042203. [CrossRef]
Kaddatz, J., Andrie, M., Reitz, R., and Kokjohn, S., 2012, “Light-Duty Reactivity Controlled Compression Ignition Combustion Using a Cetane Improver,” SAE Paper No. 2012-01-1110. [CrossRef]
Asad, U., Kumar, R., Han, X., and Zheng, M., 2011, “Precise Instrumentation of a Diesel Single Cylinder Research Engine,” J. Meas., 44(7), pp. 1261–1278. [CrossRef]
Asad, U., and Zheng, M., 2014, “Diesel Pressure Departure Ratio Algorithm for Combustion Feedback and Control,” Int. J. Engine Res., 15(1), pp. 101–111. [CrossRef]
Asad, U., Tjong, J., and Zheng, M., 2014, “Exhaust Gas Recirculation—Zero-Dimensional Modelling and Characterization for Transient Diesel Combustion Control,” Energy Convers. Manage., 86, pp. 309–324. [CrossRef]
Asad, U., and Zheng, M., 2011, “Tightened Intake Oxygen Control for Improving Diesel Low Temperature Combustion,” Proc. Inst. Mech. Eng., Part D, 225(4), pp. 513–530. [CrossRef]
Hiroyasu, H., and Arai, M., 1990, “Structure of Fuel Sprays in Diesel Engines,” SAE Trans., 99(2), pp. 1050–1061. [CrossRef]
Naber, J. D., and Siebers, D. L., 1996, “Effects of Gas Density and Vaporization on Penetration and Dispersion of Diesel Sprays,” SAE Technical Paper No. 960034. [CrossRef]
Reader, G., Asad, U., and Zheng, M., 2013, “Energy Efficiency of Phasing of HCCI Cycles,” Int. J. Energy Res., 37(3), pp. 200–210. [CrossRef]
Divekar, P., Asad, U., Han, X., Chen, X., and Zheng, M., 2014, “Study of Cylinder Charge Control for Enabling Low Temperature Combustion in Diesel Engines,” ASME J. Eng. Gas Turbines Power, 136(9), p. 091503. [CrossRef]
Asad, U., Kumar, R., Zheng, M., and Tjong, J., 2015, “Ethanol-Fuelled Low Temperature Combustion: A Pathway to Clean and Efficient Diesel Engine Cycles,” Appl. Energy (in press). [CrossRef]


Grahic Jump Location
Fig. 1

Common LTC strategies for diesel engines

Grahic Jump Location
Fig. 2

LTC fueling configurations

Grahic Jump Location
Fig. 3

Experimental setup

Grahic Jump Location
Fig. 4

Simulating the liquid spray penetration length

Grahic Jump Location
Fig. 5

Effect of EGR on HCCI combustion and emissions

Grahic Jump Location
Fig. 6

Effect of intake temperature

Grahic Jump Location
Fig. 7

Effect of engine speed on HCCI combustion

Grahic Jump Location
Fig. 8

Effect of engine speed on HCCI emissions

Grahic Jump Location
Fig. 9

Effect of injection pressure on HCCI emissions

Grahic Jump Location
Fig. 10

Injection pressure for minimum CO and THC penalty

Grahic Jump Location
Fig. 11

HCCI load limit (CR 18.2:1)

Grahic Jump Location
Fig. 12

HCCI combustion-7.5 bar IMEP (CR 15:1)

Grahic Jump Location
Fig. 13

HCCI combustion-10.1 bar IMEP (CR 15:1)

Grahic Jump Location
Fig. 14

Gasoline HCCI-10.4 bar IMEP (CR 15:1)

Grahic Jump Location
Fig. 15

Gasoline HCCI load limit (CR 15:1)

Grahic Jump Location
Fig. 16

n-Butanol HCCI without EGR (CR 18.2:1)

Grahic Jump Location
Fig. 19

Thermal efficiency variations with CR

Grahic Jump Location
Fig. 18

Thermal efficiency variations with combustion phasing

Grahic Jump Location
Fig. 17

n-Butanol HCCI with EGR (CR 18.2)



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In