Research Papers: Gas Turbines: Turbomachinery

The Application of Similitude Theory for the Performance Prediction of Radial Turbines Within Small-Scale Low-Temperature Organic Rankine Cycles

[+] Author and Article Information
Martin White

School of Mathematics,
Computer Science and Engineering,
City University London,
Northampton Square,
London EC1V 0HB, UK
e-mail: Martin.White.1@city.ac.uk

Abdulnaser I. Sayma

School of Mathematics,
Computer Science and Engineering,
City University London,
Northampton Square,
London EC1V 0HB, UK
e-mail: A.Sayma@city.ac.uk

1Corresponding author.

Contributed by the Turbomachinery Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received March 18, 2015; final manuscript received June 5, 2015; published online July 7, 2015. Editor: David Wisler.

J. Eng. Gas Turbines Power 137(12), 122605 (Jul 07, 2015) (10 pages) Paper No: GTP-15-1099; doi: 10.1115/1.4030836 History: Received March 18, 2015

For small-scale organic Rankine cycles (ORCs) to be a competitive technology, it is reasonable to assume that the same turbine design will be implemented into a range of different applications. It is therefore critical to be able to predict turbine off-design performance over a range of different operating conditions while utilizing different working fluids. Similitude theory can be used for this purpose, and it has been well validated for ideal gases. However, the same cannot be said for its applications to the organic fluids found within ORCs. This paper considers a candidate subsonic turbine design operating with R245fa and the corresponding turbine performance map. Similitude theory is used to predict the performance of the same turbine operating at different inlet conditions using R245fa, R123, and R1234yf. The similitude predictions are compared to computational fluid dynamics (CFD) results obtained using ansys CFX. The original similitude theory using turbine total inlet conditions was found to only apply within a small range of operating conditions, so a modified similitude theory has been suggested that uses the choked flow conditions instead. This modified similitude theory agrees with the CFD predictions to within 2%, right up until the choked mass flow rate. Further studies considering supersonic turbines are required to establish the applicability of similitude for applications beyond the choked pressure ratio.

Copyright © 2015 by ASME
Your Session has timed out. Please sign back in to continue.


Turboden, 2014, “Turboden–Organic Rankine Cycle Turbogenerators for Clean Electric Energy Production,” Turboden s.r.l., Brescia, Italy, accessed Nov. 15, 2015, www.turboden.eu
ORMAT, 2014, “ORMAT Technologies Inc,” Ormat Techologies, Inc., Reno, NV, accessed Nov. 15, 2015, www.ormat.com
Infinity Turbine, 2014, “Infinity Turbine,” Infinity Turbine LLC, Madison, WI, accessed Dec. 19, 2014, www.infinityturbine.com
ElectraTherm, 2014, “Energy Efficient Green Machine Heat to Power Generation System,” ElectraTherm, Inc., Reno, NV, accessed Dec. 09, 2014, www.electratherm.com
Casati, E. , Vitale, S. , Pini, M. , and Persico, P. , 2014, “Centrifugal Turbines for Mini-Organic Rankine Cycle Power Systems,” ASME J. Eng. Gas Turbines Power, 136(12), p. 122607. [CrossRef]
Lang, W. , Colonna, P. , and Almbauer, R. , 2013, “Assessment of Waste Heat Recovery From a Heavy-Duty Truck Engine by Means of an ORC Turbogenerator,” ASME J. Eng. Gas Turbines Power, 135(4), p. 042313. [CrossRef]
Bracco, R. , Clemente, S. , Micheil, D. , and Reini, M. , 2013, “Experimental Tests and Modelization of a Domestic-Scale ORC (Organic Rankine Cycle),” Energy, 58, pp. 107–116. [CrossRef]
Declaye, S. , Quoilin, S. , Guilliaume, L. , and Lemort, V. , 2013, “Experimental Study on an Open-Drive Expander Integrated Into an ORC (Organic Rankine Cycle) System With R245fa as Working Fluid,” Energy, 55, pp. 173–183. [CrossRef]
Leibowitz, H. , Smith, I. K. , and Stosic, N. , 2006, “Cost Effective Small Scale ORC Systems for Power Recovery From Low Grade Heat Sources,” ASME Paper No. IMECE2006-14284.
Quoilin, S. , Van Den Broek, M. , Declaye, S. , Dewalleg, P. , and Lemort, V. , 2013, “Techno-Economic Survey of Organic Rankine Cycle (ORC) Systems,” Renewable Sustainable Energy Rev., 22, pp. 168–186. [CrossRef]
Chen, H. , Goswami, D. Y. , and Stefanakos, E. K. , 2013, “A Review of Thermodynamic Cycles and Working Fluids for the Conversion of Low Grade Heat,” Renewable Sustainable Energy Rev., 14(9), pp. 3059–3067. [CrossRef]
Saleh, B. , Koglbauer, G. , Wendland, M. , and Fischer, J. , 2007, “Working Fluids for Low-Temperature Organic Rankine Cycles,” Energy, 32(7), pp. 1210–1221. [CrossRef]
Tchanche, B. F. , Papadakis, G. , Lambrinos, G. , and Frangoudakis, A. , 2009, “Fluid Selection for a Low-Temperature Solar Organic Rankine Cycle,” Appl. Therm. Eng., 29(11–12), pp. 2468–2476. [CrossRef]
Rashidi, M. M. , Beg, O. A. , Parsa, A. B. , and Nazari, F. , 2011, “Analysis and Optimization of a Transcritical Power Cycle With Regenerator Using Artificial Neural Networks and Genetic Algorithms,” Proc. Inst. Mech. Eng., Part A: J. Power Energy, 225(6), pp. 701–717. [CrossRef]
Sun, J. , and Li, W. , 2011, “Operation Optimization of an Organic Rankine Cycle (ORC) Heat Recovery Power Plant,” Appl. Therm. Eng., 31(11–12), pp. 2032–2041. [CrossRef]
Wang, Z. Q. , Zhou, N. J. , Guo, J. , and Wang, X. Y. , 2012, “Fluid Selection and Parametric Optimization of Organic Rankine Cycle Using Low Temperature Waste Heat,” Energy, 40(1), pp. 107–115. [CrossRef]
Kang, S. H. , 2012, “Design and Experimental Study of ORC (Organic Rankine Cycle) and Radial Turbine Using R245fa Working Fluid,” Energy, 41(1), pp. 514–524. [CrossRef]
Inoue, N. , Kaneko, A. , Watanabe, H. , Uchimura, T. , and Irie, K. , 2007, “Development of Electric Power Generation Unit Driven by Waste Heat (Study on Working Fluids and Expansion Turbines),” ASME Paper No. GT2007-27749.
Li, J. , Pei, G. , Ji, J. , Bai, X. , Li, P. , and Xia, L. , 2014, “Design of the ORC (Organic Rankine Cycle) Condensation Temperature With Respect to the Expander Characteristics for Domestic CHP (Combined Heat and Power) Applications,” Energy, 77, pp. 579–590. [CrossRef]
Sauret, E. , and Gu, Y. , 2014, “Three-Dimensional Off-Design Numerical Analysis of an Organic Rankine Cycle Radial-Inflow Turbine,” Appl. Energy, 135, pp. 202–211. [CrossRef]
Moustapha, H. , Zelesky, M. F. , Baines, N. C. , and Japiske, D. , 2003, Axial and Radial Turbines, Concepts ETI, White River Junction, VT.
Aungier, R. H. , 2006, Turbine Aerodynamics: Axial-Flow and Radial In-Flow Turbine Design and Analysis, ASME, New York.
Manente, G. , Toffolo, A. , Lazzaretto, A. , and Paci, M. , 2013, “An Organic Rankine Cycle Off-Design Model for the Search of the Optimal Control Strategy,” Energy, 58, pp. 97–106. [CrossRef]
Calise, F. , Capuozzo, C. , Carontenuto, A. , and Vanoil, L. , 2014, “Thermoeconomic Analysis and Off-Design Performance of an Organic Rankine Cycle Powered by Medium Temperature Heat Sources,” Solar Energy, 103, pp. 595–609. [CrossRef]
Li, J. , Pei, G. , Li, Y. , Wang, D. , and Ji, J. , 2013, “Examination of the Expander Leaving Loss in Variable Organic Rankine Cycle Operation,” Energy Convers. Manage., 65, pp. 66–74. [CrossRef]
Ventura, C. A. M. , Jacobs, P. A. , Rowlands, A. S. , Petrie-Repar, P. , and Sauret, E. , 2012, “Preliminary Design and Performance Estimation of Radial Inflow Turbines: An Automated Approach,” ASME J. Fluids Eng., 134(3), p. 031102. [CrossRef]
Pan, L. , and Wang, H. , 2013, “Improved Analysis of Organic Rankine Cycle Based on Radial Flow Turbine,” Appl. Therm. Eng., 61(2), pp. 606–615. [CrossRef]
Fiaschi, D. , Manfrida, G. , and Maraschiello, F. , 2015, “Design and Performance Prediction of Radial ORC Turboexpanders,” Appl. Energy, 138, pp. 517–532. [CrossRef]
Klonowicz, P. , Heberle, F. , Preissinger, M. , and Bruggermann, D. , 2014, “Significance of Loss Correlations in Performance Prediction of Small Scale, Highly Loaded Turbine Stages Working in Organic Rankine Cycles,” Energy, 72, pp. 322–330. [CrossRef]
Lemmon, E. W. , Huber, M. L. , and McLinden, M. O. , 2013, NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties-refprop: Version 9.1, National Institute of Standards and Technology, Standard Data Program, Gaithersburg, MD.
Wheeler, P. S. , and Ong, J. , 2013, “The Role of Dense Gas Dynamics on Organic Rankine Cycle Turbine Performance,” ASME J. Eng. Gas Turbines Power, 135(10), p. 102603. [CrossRef]
White, M. , and Sayma, A. I. , 2015, “The One-Dimensional Meanline Design of Radial Turbines for Small Scale Low Temperature Organic Rankine Cycles,” ASME Paper No. GT2015-44133.
Lujan, J. M. , Serrano, J. R. , Dolz, V. , and Sanchez, J. , 2012, “Model of the Expansion Process for R245fa in an Organic Rankine Cycle (ORC),” Appl. Therm. Eng., 40, pp. 248–257. [CrossRef]
Wheeler, P. S. , and Ong, J. , 2014, “A Study of the Three-Dimensional Unsteady Real-Gas Flows Within a Transonic ORC Turbine,” ASME Paper No. GT2014-25475.


Grahic Jump Location
Fig. 1

Deviation in Reynolds number with variations in turbine total inlet conditions for R245fa assuming that the blade Mach number has been conserved (the dots represent the operating conditions considered within this paper)

Grahic Jump Location
Fig. 2

Variation in thermodynamic properties over a range of operating conditions for superheated R245fa between operating point and design point: (a) percentage deviation in density, (b) percentage deviation in speed of sound, (c) percentage deviation in dynamic viscosity, and (d) variation in compressibility factor

Grahic Jump Location
Fig. 3

Results from grid independence study showing the percentage difference in mass flow rate for three meshes, compared to the result obtained for the finest mesh

Grahic Jump Location
Fig. 4

Variation of flow coefficient with head coefficient at 80%, 100%, and 120% of the design blade Mach number for the developed ORC turbine operating with R245fa

Grahic Jump Location
Fig. 5

Variation of isentropic total-to-static efficiency with head coefficient at 80%, 100%, and 120% of the design blade Mach number for the developed ORC turbine operating with R245fa

Grahic Jump Location
Fig. 6

Comparison between the flow coefficient predicted by similitude theory and the flow coefficient found from the CFD results for the R245fa operating points

Grahic Jump Location
Fig. 7

Comparison between the isentropic total-to-static isentropic efficiency predicted by similitude theory and the efficiency found from the CFD results for the R245fa operating points

Grahic Jump Location
Fig. 8

Comparison between the CFD results for R245fa cases 6–8 and the nondimensional performance curves used during the application of similitude theory: (a) case 6, (b) case 7, and (c) case 8

Grahic Jump Location
Fig. 10

Comparison between the isentropic total-to-static isentropic efficiency predicted by the updated similitude theory and the efficiency found from the CFD results for the R245fa operating points

Grahic Jump Location
Fig. 9

Comparison between the flow coefficient predicted by the updated similitude theory and the flow coefficient found from the CFD results for the R245fa operating points

Grahic Jump Location
Fig. 11

Summary of the stator vane performance over a range of flow coefficients. Bottom group of data points refers to the throat, while the top group of data points refers to the stator outlet set at the rotor inlet radius. The dashed lines represent the change from subsonic to supersonic operation.

Grahic Jump Location
Fig. 12

Distribution of Mach number within the turbine stator for case 8, and flow coefficient of 2.92 × 10−4

Grahic Jump Location
Fig. 13

Comparisons between the predictions made for the flow coefficient and isentropic efficiency by similitude theory and CFD for the alternative working fluids: (a) R123 flow coefficient, (b) R123 isentropic efficiency, (c) R1234yf flow coefficient, and (d) R1234yf isentropic efficiency



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In