Research Papers: Gas Turbines: Combustion, Fuels, and Emissions

Shockless Explosion Combustion: Experimental Investigation of a New Approximate Constant Volume Combustion Process

[+] Author and Article Information
Thoralf G. Reichel

Chair of Fluid Dynamics,
Technische Universität Berlin,
Berlin 10623, Germany
e-mail: thoralf.reichel@tu-berlin.de

Jan-Simon Schäpel, Rudibert King

Chair of Measurement and Control,
Technische Universität Berlin,
Berlin 10623, Germany

Bernhard C. Bobusch, Christian Oliver Paschereit

Chair of Fluid Dynamics,
Technische Universität Berlin,
Berlin 10623, Germany

Rupert Klein

Department of Mathematics,
Geophysical Fluid Dynamics,
Freie Universität Berlin,
Berlin 14195, Germany

1Corresponding author.

Contributed by the Combustion and Fuels Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received June 21, 2016; final manuscript received June 23, 2016; published online September 13, 2016. Editor: David Wisler.

J. Eng. Gas Turbines Power 139(2), 021504 (Sep 13, 2016) (7 pages) Paper No: GTP-16-1257; doi: 10.1115/1.4034214 History: Received June 21, 2016; Revised June 23, 2016

Approximate constant volume combustion (aCVC) is a promising way to achieve a step change in the efficiency of gas turbines. This work investigates a recently proposed approach to implement aCVC in a gas turbine combustion system: shockless explosion combustion (SEC). The new concept overcomes several disadvantages such as sharp pressure transitions, entropy generation due to shock waves, and exergy losses due to kinetic energy which are associated with other aCVC approaches such as pulsed detonation combustion. The combustion is controlled via the fuel/air mixture distribution which is adjusted such that the entire fuel/air volume undergoes a spatially quasi-homogeneous auto-ignition. Accordingly, no shock waves occur and the losses associated with a detonation wave are not present in the proposed system. Instead, a smooth pressure rise is created due to the heat release of the homogeneous combustion. An atmospheric combustion test rig is designed to investigate the auto-ignition behavior of relevant fuels under intermittent operation, currently up to a frequency of 2 Hz. Application of OH*– and dynamic pressure sensors allows for a spatially and time-resolved detection of ignition delay times and locations. Dimethyl ether (DME) is used as fuel since it exhibits reliable auto-ignition already at 920 K mixture temperature and ambient pressure. First, a model-based control algorithm is used to demonstrate that the fuel valve can produce arbitrary fuel profiles in the combustion tube. Next, the control algorithm is used to achieve the desired fuel stratification, resulting in a significant reduction in spatial variance of the auto-ignition delay times. This proves that the control approach is a useful tool for increasing the homogeneity of the auto-ignition.

Copyright © 2017 by ASME
Your Session has timed out. Please sign back in to continue.


Stathopoulus, P. , Vinkeloe, J. , and Paschereit, C. O. , 2015, “ Thermodynamic Evaluation of Constant Volume Combustion for Gas Turbine Power Cycles,” 11th International Gas Turbine Congress, Tokyo, Japan, Nov. 15–20.
Putnam, A. , Belles, F. , and Kentfield, J. , 1986, “ Pulse Combustion,” Prog. Energy Combust. Sci., 12(1), pp. 43–79. [CrossRef]
Roy, G. , Frolov, S. , Borisov, A. , and Netzer, D. , 2004, “ Pulse Detonation Propulsion: Challenges, Current Status, and Future Perspective,” Prog. Energy Combust. Sci., 30(6), pp. 545–672. [CrossRef]
Lu, F. K. , and Braun, E. M. , 2014, “ Rotating Detonation Wave Propulsion: Experimental Challenges, Modeling, and Engine Concepts,” J. Propul. Power, 30(5), pp. 1125–1142. [CrossRef]
Akbari, P. , Nalim, R. , and Mueller, N. , 2006, “ A Review of Wave Rotor Technology and Its Applications,” ASME J. Eng. Gas Turbines Power, 128(4), pp. 717–735. [CrossRef]
Bobusch, B. C. , Berndt, P. , Paschereit, C. O. , and Klein, R. , 2014, “ Shockless Explosion Combustion: An Innovative Way of Efficient Constant Volume Combustion in Gas Turbines,” Combust. Sci. Technol., 186(10–11), pp. 1680–1689. [CrossRef]
Bobusch, B. C. , 2015, “ Fluidic Devices for Realizing the Shockless Explosion Combustion Process,” Ph.D. thesis, Technische Universität, Berlin.
Bobusch, B. C. , Berndt, P. , Paschereit, C. O. , and Klein, R. , 2015, “ Investigation of Fluidic Devices for Mixing Enhancement for the Shockless Explosion Combustion Process,” Active Flow and Combustion Control 2014, Springer, Berlin, pp. 281–297.
Berndt, P. , Klein, R. , and Paschereit, C. O. , 2016, “ A Kinetics Model for the Shockless Explosion Combustion,” ASME Paper No. GT2016-57678.
Cai, L. , and Pitsch, H. , 2015, “ Tailoring Fuels for a Shockless Explosion Combustor,” Active Flow and Combustion Control 2014 (Notes on Numerical Fluid Mechanics and Multidisciplinary Design, Vol. 127), R. King, ed., Springer International Publishing, Cham, Switzerland, pp. 299–315.
Bobusch, B. C. , Woszidlo, R. , Bergada, J. M. , Nayeri, C. N. , and Paschereit, C. O. , 2013, “ Experimental Study of the Internal Flow Structures Inside a Fluidic Oscillator,” Exp. Fluids, 54(6), pp. 1–12. [CrossRef]
Bobusch, B. C. , Woszidlo, R. , Krüger, O. , and Paschereit, C. O. , 2013, “ Numerical Investigations on Geometric Parameters Affecting the Oscillation Properties of a Fluidic Oscillator,” AIAA Paper No. 2013-2709.
Lacarelle, A. , and Paschereit, C. O. , 2012, “ Increasing the Passive Scalar Mixing Quality of Jets in Crossflow With Fluidics Actuators,” ASME J. Eng. Gas Turbines Power, 134(2), p. 021503. [CrossRef]
Li, H. , Wehe, S. D. , and McManus, K. R. , 2011, “ Real-Time Equivalence Ratio Measurements in Gas Turbine Combustors With a Near-Infrared Diode Laser Sensor,” Proc. Combust. Inst., 33(1), pp. 717–724. [CrossRef]
Ljung, L. , 1999, System Identification: Theory for the User, 2nd ed., Prentice-Hall, Englewood Cliffs, NJ.
Bristow, D. A. , Tharayil, M. , and Alleyne, A. G. , 2006, “ A Survey of Iterative Learning Control,” IEEE Control Syst., 26(3), pp. 96–114. [CrossRef]
Amann, N. , Owens, D. H. , and Rogers, E. , 1996, “ Iterative Learning Control Using Optimal Feedback and Feedforward Actions,” Int. J. Control, 65(2), pp. 277–293. [CrossRef]


Grahic Jump Location
Fig. 1

Ideal cycle comparison for constant volume combustion (Humphrey) and constant pressure combustion (Joule): T-S diagram (left); efficiency over pressure ratio (right); from Ref. [1]

Grahic Jump Location
Fig. 2

Schematic of the SEC cycle

Grahic Jump Location
Fig. 3

Effect of equivalence ratio stratification on ignition delay time distribution

Grahic Jump Location
Fig. 4

Schematic of the atmospheric SEC test rig

Grahic Jump Location
Fig. 5

Section view of the inlet section with the fluidic diode and fuel injection ring which applies fluidic oscillators

Grahic Jump Location
Fig. 6

Diagnostics of the combustion test rig

Grahic Jump Location
Fig. 7

Identification experiment: (a) Fuel concentration and (b) valve input: five random amplitude sequences

Grahic Jump Location
Fig. 8

Cross-validation experiment: (a) Fuel concentration and (b) valve input: five random amplitude sequences

Grahic Jump Location
Fig. 9

Example of timing sequence for main air, fuel, and PMT sensor readings over one ignition cycle, amplitudes are arbitrarily chosen

Grahic Jump Location
Fig. 10

ILC: convergence speed of the control error

Grahic Jump Location
Fig. 11

Converged ILC after 100 iterations: (a) Fuel concentration compared to the reference and (b) valve input generated by the ILC

Grahic Jump Location
Fig. 12

Starting condition for the ILC (solid/crosses) and converged ILC after 500 iterations (dashed/cirles). (a) ignition time compared to the reference and (b) valve input generated by the ILC.

Grahic Jump Location
Fig. 13

ILC: Variance of the detected ignition times (thin line) and its moving average (thick line)



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In