0
Research Papers: Gas Turbines: Structures and Dynamics

Brush Seal Frictional Heat Generation—Test Rig Design and Validation Under Steam Environment

[+] Author and Article Information
Markus Raben

TU Braunschweig,
Institute of Jet Propulsion and Turbomachinery,
Hermann-Blenk-Str., 37,
Braunschweig 38108, Germany
e-mail: m.raben@ifas.tu-bs.de

Jens Friedrichs

TU Braunschweig,
Institute of Jet Propulsion and Turbomachinery,
Hermann-Blenk-Str., 37,
Braunschweig 38108, Germany
e-mail: j.friedrichs@ifas.tu-bs.de

Johan Flegler

Siemens AG,
Power and Gas Division,
Rheinstr. 100,
Mülheim a. d. Ruhr 45478, Germany
e-mail: johan.flegler@siemens.com

1Corresponding author.

Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received July 10, 2016; final manuscript received July 18, 2016; published online October 4, 2016. Editor: David Wisler.The content of this paper is copyrighted by Siemens Energy, Inc. and is licensed to ASME for publication and distribution only. Any inquiries regarding permission to use the content of this paper, in whole or in part, for any purpose must be addressed to Siemens Energy, Inc. directly.

J. Eng. Gas Turbines Power 139(3), 032502 (Oct 04, 2016) (9 pages) Paper No: GTP-16-1320; doi: 10.1115/1.4034500 History: Received July 10, 2016; Revised July 18, 2016

Sealing technology is a key feature to improve efficiency of steam turbines for both new power stations and modernization projects. One of the most powerful sealing alternatives for reducing parasitic leakages in the blade path of a turbine as well as in shaft sealing areas is the use of brush seals, which are also widely used in gas turbines and turbo compressors. The advantage of brush seals over other sealing concepts is based on the narrow gap that is formed between the brush seal bristle tips and the mating rotor surface together with its radial adaptivity. While the narrow gap between the bristle tips and the rotor leads to a strongly decreased flow through the seal compared with conventional turbomachinery seals, it is important to be aware of the tight gap that can be bridged by relative motion between the rotor and the brush seal, leading to a contact of the bristles and the rotor surface. Besides abrasive wear occurrence, the friction between the bristles and the rotor leads to heat generation which can be detrimental to turbine operation due to thermal effects, leading to rotor bending connected to increasing shaft vibrations. In order to investigate the frictional heat generation of brush seals, different investigation concepts have been introduced through the past years. To broaden the knowledge about frictional heat generation and to make it applicable for steam turbine applications, a new testing setup was designed for the steam test rig of the Institute of Jet Propulsion and Turbomachinery—TU Braunschweig, Germany, enabling temperature measurements in the rotor body under stationary and transient operation in steam by using rotor-integrated thermocouples. Within this paper, the development of the instrumented new rotor design and all relevant parts of the new testing setup is shown along with the testing ability by means of the validation of the test rig concept and the achieved measurement accuracy. First results prove that the new system can be used to investigate frictional heat generation of brush seals under conditions relevant for steam turbine shaft seals.

FIGURES IN THIS ARTICLE
<>
Copyright © 2016 by Siemens AG
Your Session has timed out. Please sign back in to continue.

References

Schwarz, H. , Friedrichs, J. , and Flegler, J. , 2014, “ Axial Inclination of the Bristle Pack, a New Design Parameter of Brush Seals for Improved Operational Behavior in Steam Turbines,” ASME Paper No. GT2014-26330.
Owen, A. K. , Jones, T. V. , Guo, S. M. , and Hogg, S. I. , 2003, “ An Experimental and Theoretical Study of Brush Seal and Shaft Thermal Interaction,” ASME Paper No. GT2003-38276.
Demiroglu, M. , and Tichy, J. A. , 2007, “ An Investigation of Heat Generation Characteristics of Brush Seals,” ASME Paper No. GT2007-28043.
Pfefferle, D. , Dullenkopf, K. , and Bauer, H.-J. , 2011, “ Design and Validation of a New Test Rig for Brush Seal Testing Under Engine Relevant Conditions,” ASME Paper No. GT2011-45107.
Raben, M. , Friedrichs, J. , Flegler, J. , and Helmis, T. , 2015, “ Brush Seals Used in Steam Environments—Chronological Wear Development and the Impact of Different Seal Designs,” ASME Paper No. GT2015-43184.
Raben, M. , Schwarz, H. , and Friedrichs, J. , 2013, “ Operating Performance and Wear Investigations of Brush Seals for Steam Turbine Applications,” ASME Paper No. GT2013-95442.
Schwarz, H. , Friedrichs, J. , and Flegler, J. , 2012, “ Design Parameters of Brush Seals and their Impact on Seal Performance,” ASME Paper No. GT2012-68956.
Crudgington, P. F. , 1998, “ Brush Seal Performance Evaluation,” 34th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, AIAA Paper No. 98-3172.
Berard, G. , and Short, J. , 1999, “ Influence of Design Features on Brush Seal Performance,” 35th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, AIAA Paper No. 99-2685.
Neef, M. , Sürken, N. , Walkenhorst, J. , and Sulda, E. , 2006, “ Design Features and Performance Details of Brush Seals For Turbine Applications,” ASME Paper No. GT2006-90404.
Demiroglu, M. , Gursoy, M. , and Tichy, J. A. , 2007, “ An Investigation of Tip Force Characteristics of Brush Seals,” ASME Paper No. GT2007-28042.
Dogu, Y. , and Aksit, M. , 2006, “ Brush Seal Temperature Distribution Analysis,” ASME J. Eng. Gas Turbines Power., 128(3), pp. 599–609. [CrossRef]
Crudgington, P. F. , and Bowsher, A. , 2002, “ Brush Seal Pack Hysteresis,” 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, AIAA Paper No. 2002-3794.
Qiu, B. , and Li, J. , 2013, “ Numerical Investigations on the Heat Transfer Behavior of Brush Seals Using Combined Computational Fluid Dynamics and Finite Element Method,” ASME J. Heat Transfer, 135(12), p. 122601. [CrossRef]
Crudgington, P. F. , Bowsher, A. , Lloyd, D. , and Walia, J. , 2009, “ Bristle Angle Effects on Brush Seal Contact Pressures,” 45th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, AIAA Paper No. 2009-5168.
Franceschini, G. , Morgan, J. J. , Jones, T. V. , and Gillespie, D. R. H. , 2006, “ A Slow-Speed Rotating Test Facility for Characterising the Stiffness of Brush Seals,” ASME Paper No. GT2006-91335.
Franceschini, G. , Jones, T. V. , and Gillespie, D. R. H. , 2010, “ Improved Understanding of Blow-Down in Filament Seals,” ASME J. Turbomach., 132(4), p. 041004. [CrossRef]
Aksit, M. , Dogu, Y. , Kandemir, I. , and Kizil, H. , 2006, “ An Investigation of Pressure Stiffness Coupling in Brush Seals,” Eleventh International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-11-4), Honolulu, HI, Feb. 26–Mar. 2. http://research.sabanciuniv.edu/1144/1/3011800000701.pdf
Bidkar, R. A. , Demiroglu, M. , Zheng, X. , and Turnquist, N. , 2011, “ Stiffness Measurement for Pressure-Loaded Brush Seals,” ASME Paper No. GT2011-45399.
Fellenstein, J. A. , and DellaCorte, C. , 1995, “ A New Tribological Test for Candidate Brush Seal Materials Evaluation,” Technical Report No. NASA/TM-106753.
Duran, E. T. , Ozmusul, M. , and Aksit, M. F. , 2015, “ Brush Seal Structural Analysis and Correlation With Tests for Turbine Conditions,” ASME Paper No. GT2015-44067.
Duran, E. T. , Ozmusul, M. , and Aksit, M. F. , 2015, “ CAE Based Brush Seal Characterization for Stiffness and Stress Levels,” ASME Paper No. GT2015-44068.
Duran, E. T. , Ozmusul, M. , and Aksit, M. F. , 2015, “ Brush Seal Free State Stiffness Analyses, Tests and Inspection on Dynamic Effects,” ASME Paper No. GT2015-44069.
Long, C. A. , and Marras, Y. , 1995, “ Contact Force Measurements Under a Brush Seal,” ASME Paper No. 95-GT-211.
Büscher, S. , 2010, “ Untersuchung von mehrstufigen Bürstendichtungen für Dampfturbinen,” Ph.D thesis, TU Braunschweig, Institute of Jet Propulsion and Turbomachinery, Verlag und Bildarchiv W.H. Faragallah, Braunschweig, Germany.
Pröstler, S. , 2005, “ Modellierung und numerische Berechnungen von Wellenabdichtungen in Bürstenbauart,” Ph.D thesis, Bochum University, Verlag Dr. Hut, Munich, Germany.

Figures

Grahic Jump Location
Fig. 1

Clamped seal design (left) and welded seal design (right)

Grahic Jump Location
Fig. 2

Schematic heat transfer mechanisms

Grahic Jump Location
Fig. 4

New rotor design: (a) 3D CAD model and (b) section view center body (A-A)

Grahic Jump Location
Fig. 5

Superficial TC wiring

Grahic Jump Location
Fig. 6

Rotor instrumentation—measuring positions: (a) instrumentation displacement end and (b) instrumentation drive end

Grahic Jump Location
Fig. 7

Radial rotor growth

Grahic Jump Location
Fig. 8

Open rotor end—redesigned thrust bearing

Grahic Jump Location
Fig. 9

Reference temperature (RTD)

Grahic Jump Location
Fig. 10

Temperature measurements displacement end (a) TC nomenclature and (b) measurements 24 h (stationary operation 30 bar)

Grahic Jump Location
Fig. 11

Calculated rotor temperature profile, displacement end

Grahic Jump Location
Fig. 12

Difference between calculations (FEA) and measurements, displacement end

Grahic Jump Location
Fig. 13

Compensation area—additional measuring positions

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In