Research Papers: Gas Turbines: Structures and Dynamics

A Rotordynamic, Thermal, and Thrust Load Performance Gas Bearing Test Rig and Test Results for Tilting Pad Journal Bearings and Spiral Groove Thrust Bearings

[+] Author and Article Information
Aaron M. Rimpel

Southwest Research Institute,
San Antonio, TX 78238
e-mail: aaron.rimpel@swri.org

Giuseppe Vannini

Baker Hughes,
Florence 50127, Italy
e-mail: giuseppe.vannini@bhge.com

Jongsoo Kim

Waukesha Bearings Corporation,
Pewaukee, WI 53072
e-mail: jkim@waukbearing.com

Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received June 21, 2016; final manuscript received July 14, 2017; published online August 16, 2017. Editor: David Wisler.

J. Eng. Gas Turbines Power 139(12), 122501 (Aug 16, 2017) (11 pages) Paper No: GTP-16-1259; doi: 10.1115/1.4037315 History: Received June 21, 2016; Revised July 14, 2017

A high-speed gas bearing test rig was developed to characterize rotordynamic, thermal, and thrust load performance of gas bearings being developed for an oil-free turboexpander. The radial bearings (RBs) tested in this paper were tilting pad journal bearings with radial compliance features that allow the bearing bore to increase to accommodate shaft growth, and the thrust bearings (TBs) were a spiral groove type with axial compliance features. The TB accounts for over 90% of the combined bearing power consumption, which has a cubic relationship with speed and increases with case pressure. RB circumferential pad temperatures increased approximately with speed to the fourth or fifth power, with slightly higher temperature rise for lower case pressure. Maximum steady-state bearing pad temperatures increase with increasing speed for similar cooling mass flow rates; however, only the TB showed a significant increase in temperature with higher case pressure. The TBs were stable at all speeds, but the load capacity was found to be lower than anticipated, apparently due to pad deformations caused by radial temperature gradients in the stator. More advanced modeling approaches have been proposed to better understand the TB thermal behavior and to improve the TB design. Finally, the RBs tested were demonstrated to be stable up to the design speed of 130 krpm, which represents the highest surface speed for tilting pad gas bearings tested in the literature.

Copyright © 2017 by ASME
Your Session has timed out. Please sign back in to continue.



Grahic Jump Location
Fig. 3

Computer-aided design model of gas bearing test rig: (a) external view and (b) cross section

Grahic Jump Location
Fig. 4

Schematic of air flow loop

Grahic Jump Location
Fig. 5

Bearing internal cooling flow configurations

Grahic Jump Location
Fig. 6

Bearing pad thermocouples

Grahic Jump Location
Fig. 7

Combined bearing power loss for different speeds and case pressures

Grahic Jump Location
Fig. 8

Average RB circumferential pad temperature rise from leading to trailing edge

Grahic Jump Location
Fig. 9

Maximum steady-state bearing pad temperatures for different speeds and case pressures: (a) RB pad temperatures and (b) TB pad temperatures

Grahic Jump Location
Fig. 10

TB pad temperatures during low case pressure test, no external thrust load

Grahic Jump Location
Fig. 11

Relative rotor axial position versus speed during low case pressure test, no external thrust load

Grahic Jump Location
Fig. 12

Identification of internal thrust force at 80 krpm and low case pressure

Grahic Jump Location
Fig. 13

Waterfall plot of vibration during load capacity test: (a) lateral and (b) axial

Grahic Jump Location
Fig. 14

Thermal response of loaded TB during load capacity test

Grahic Jump Location
Fig. 15

Waterfall plot of lateral vibration during final shut down: (a) sampled at 10 kHz for 0.32 s and (b) sampled at 10 kHz for 0.04 s

Grahic Jump Location
Fig. 16

Orbit plots at different points of final shut down: (a) point A, (b) between A and B, and (c) between C and D

Grahic Jump Location
Fig. 17

RB pad temperatures during final shut down

Grahic Jump Location
Fig. 18

Photograph of RB showing condition of pad coating and yielded radial compliance feature

Grahic Jump Location
Fig. 19

Bearing condition before and after yielding

Grahic Jump Location
Fig. 20

Gas journal bearing operating speed experience




Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In