Two-CCD binocular stereo vision systems using pinhole model are attracting research interest in many important fields such as 3-D coordinate measurement. However, new system modeling is difficult because of lack of fundamental imaging formation theory. In this paper, in order to measure a 3-D surface, we demonstrate how a binocular stereo vision system can be modeled by the proposed skew ray tracing method to study the geometric relations between the binocular camera images and the 3-D surface. In order to investigate the overall accuracy and resolution of this system, the influence of infinitesimal camera reading errors on measured coordinate errors is determined by sensitivity analysis. Experimental verification demonstrates that the performance of the proposed system is excellent.
Skip Nav Destination
Article navigation
March 2004
Technical Papers
A New Model of Binocular Stereo Coordinate Measurement System Based on Skew Ray Tracing
Psang Dain Lin,
Psang Dain Lin
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan 70101
**
Search for other works by this author on:
Te-tan Liao
Te-tan Liao
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan
(Current Affiliation: Associate Professor, Department of Mechanical Engineering, Far East College, Tainan, Taiwan)
Search for other works by this author on:
Psang Dain Lin
**
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan 70101
Te-tan Liao
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan
(Current Affiliation: Associate Professor, Department of Mechanical Engineering, Far East College, Tainan, Taiwan)
Contributed by the Dynamic Systems, Measurement and Control Division of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for publication in the ASME JOURNAL OF DYNAMIC SYSTEMS, MEASUREMENT, AND CONTROL. Manuscript received by the ASME Dynamic Systems and Control Division September 25, 2001; final revision, July 17, 2003. Associate Editor: M. Goldfarb.
J. Dyn. Sys., Meas., Control. Mar 2004, 126(1): 102-114 (13 pages)
Published Online: April 12, 2004
Article history
Received:
September 25, 2001
Revised:
July 17, 2003
Online:
April 12, 2004
Citation
Lin, P. D., and Liao, T. (April 12, 2004). "A New Model of Binocular Stereo Coordinate Measurement System Based on Skew Ray Tracing ." ASME. J. Dyn. Sys., Meas., Control. March 2004; 126(1): 102–114. https://doi.org/10.1115/1.1649975
Download citation file:
Get Email Alerts
Offline and Online Exergy-Based Strategies for Hybrid Electric Vehicles
J. Dyn. Sys., Meas., Control (May 2025)
Multi Combustor Turbine Engine Acceleration Process Control Law Design
J. Dyn. Sys., Meas., Control
A Distributed Layered Planning and Control Algorithm for Teams of Quadrupedal Robots: An Obstacle-Aware Nonlinear Model Predictive Control Approach
J. Dyn. Sys., Meas., Control (May 2025)
Active Data-Enabled Robot Learning of Elastic Workpiece Interactions
J. Dyn. Sys., Meas., Control (May 2025)
Related Articles
Modeling and Sensitivity Analysis of Laser Tracking Systems by Skew-Ray Tracing Method
J. Manuf. Sci. Eng (August,2005)
Skew Ray Tracing and Sensitivity Analysis of Geometrical Optics
J. Manuf. Sci. Eng (May,2000)
Three-Dimensional Analysis of a Concentrated Solar Flux
J. Sol. Energy Eng (February,2008)
Evaluating View Factors Using a Hybrid Monte-Carlo Method
J. Heat Transfer (December,2022)
Related Proceedings Papers
Related Chapters
Fundamentals of Ray Tracing
The Monte Carlo Ray-Trace Method in Radiation Heat Transfer and Applied Optics
Sensitivity Analysis of Influencing Factors of Bedding Bank Rock Slope Based on Orthogonal Design
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
Sensitivity Analysis on the Effect of the Seepage from Underground Hydraulic Tunnel under High Internal Water Pressure
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)