This paper presents a method to combine computational fluid dynamics (CFD) modeling with subscale experiments to improve full-scale propulsor performance prediction. Laboratory experiments were conducted on subscale models of the NUWC Light underwater vehicle in the 0.3048 m × 0.3048 m water tunnel located at the Naval Undersea Warfare Center in Newport, Rhode Island. This model included an operational rim-driven ducted post-swirl propulsor. Laser Doppler Velocimetry was used to measure several velocity profiles along the hull. The experimental data were used in this project to validate the CFD models constructed using the commercial CFD software package, Fluent®. Initially, axisymmetric two-dimensional simulations investigated the bare hull, hull only case, and a shrouded body without the propulsor. These models were selected to understand the axisymmetric flow development and investigate methods to best match the propulsor inflow. A variety of turbulence models were investigated and ultimately the numerical and experimental velocity profiles were found to match within 3%. Full 3D flow simulations were then conducted with an operating propulsor and compared with the corresponding subscale experimental data. Finally, simulations were conducted for full-scale tests and compared with actual open-water data. While the open-water data was limited to propulsor rpm and vehicle velocity, the operating advance ratio could be determined as well as the estimated vehicle thrust. This provided a method to utilize CFD/experiments to bridge the gap between subscale and full-scale tests. The predicted open-water advance ratio was 10.3% higher than the experimental value, as compared with the 28% difference previously found from a linear extrapolation of Reynolds number from model scale to full scale. This method was then applied to two different research propulsor geometries and led to agreement between computational and experimental advance ratios on the order of 2%.
Skip Nav Destination
e-mail: Amanda.Dropkin@navy.mil
Article navigation
August 2011
Research Papers
Combined Experimental/Numerical Development of Propulsor Evaluation Capability
Amanda M. Dropkin,
e-mail: Amanda.Dropkin@navy.mil
Amanda M. Dropkin
Naval Undersea Warfare Center
, Code 8233, Building 1302/2, Newport, RI 02841
Search for other works by this author on:
Stephen A. Huyer,
Stephen A. Huyer
Naval Undersea Warfare Center
, Code 8233, Building 1302/2, Newport, RI 02841
Search for other works by this author on:
Charles Henoch
Charles Henoch
Naval Undersea Warfare Center
, Code 8233, Building 1302/2, Newport, RI 02841
Search for other works by this author on:
Amanda M. Dropkin
Naval Undersea Warfare Center
, Code 8233, Building 1302/2, Newport, RI 02841e-mail: Amanda.Dropkin@navy.mil
Stephen A. Huyer
Naval Undersea Warfare Center
, Code 8233, Building 1302/2, Newport, RI 02841
Charles Henoch
Naval Undersea Warfare Center
, Code 8233, Building 1302/2, Newport, RI 02841J. Fluids Eng. Aug 2011, 133(8): 081105 (9 pages)
Published Online: September 2, 2011
Article history
Received:
September 3, 2010
Revised:
May 6, 2011
Online:
September 2, 2011
Published:
September 2, 2011
Citation
Dropkin, A. M., Huyer, S. A., and Henoch, C. (September 2, 2011). "Combined Experimental/Numerical Development of Propulsor Evaluation Capability." ASME. J. Fluids Eng. August 2011; 133(8): 081105. https://doi.org/10.1115/1.4004387
Download citation file:
Get Email Alerts
Cited By
Related Articles
Integrated Motor/Propulsor Duct Optimization for Increased Vehicle and Propulsor Performance
J. Fluids Eng (April,2011)
Direct Constrained Computational Fluid Dynamics Based Optimization of Three-Dimensional Blading for the Exit Stage of a Large Power Steam Turbine
J. Eng. Gas Turbines Power (January,2003)
Investigation on the Propulsion of a Pump-Jet Propulsor in an Effective Wake
J. Fluids Eng (May,2022)
Related Proceedings Papers
Related Chapters
Computational Modeling of Dynamic Planing Forces
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Cavitating Structures at Inception in Turbulent Shear Flow
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Introduction
Design and Analysis of Centrifugal Compressors