Intake flow structure was studied using various port geometries in a four-valve heavy-duty diesel engine. Swirl ratio, LDV measurements of bulk flow and turbulence, and flow visualization experiments were conducted on a steady-state bench rig. In addition to the standard production port, archetypal intake port flows (swirl, anti-swirl and tumble) were created using intake valve shrouds. These flow types are not usually found in heavy-duty engines, which typically employ quiescent combustion chamber designs. However, recent CFD analyses have indicated that intake flow structures can significantly influence engine pollutant emissions (Fuchs and Rutland, 1998). Thus, it was of interest to characterize these flows in a heavy-duty engine. The measured swirl and axial velocity components were analyzed to reveal the swirl and tumble generation mechanisms, and the LDV data compared favorably with the swirl meter results. The flow visualization confirmed the existence of flow recirculation regions under the intake valves also seen in the LDV data. These flow structures help to explain the origins of the overall swirl and tumble flow fields. The results were also compared with available CFD predictions made using the same port configurations. The measured swirl levels were found to agree with the CFD trends. However, in some cases quantitative differences were found, presumably due to the effect of piston motion in the actual engine. These differences need to be accounted for when evaluating port designs from steady-flow measurements, especially in cases with high tumble flow components. [S0742-4795(00)00804-8]

Issue Section:
In-Cylinder Processes
Keywords:
internal combustion engines, flow simulation, swirling flow, computational fluid dynamics, valves, flow visualisation
Topics:
Cylinders, Flow (Dynamics), Flow visualization, Valves, Engines, Diesel engines, Turbulence
1.
Weaving, J. H., 1990, Internal Combustion Engineering, Elsevier Science, New York, pp. 333–384.
2.
Qi, G., Zhou, J., Liu, Z., and Chen, J., 1995, “The Study of an Optimum Method for Inlet Port Performance in a D.I. Diesel Engine,” SAE Paper 952056.
3.
Stone, C. R., and Ladommatos, R., 1992, “The Measurement and Analysis of Swirl in Steady Flow,” SAE Paper 921642.
4.
Ogawa, H., Matsui, Y., Kimura, S., and Kawashima, J., 1996, “Three-Dimensional Computation of the Effects of the Swirl Ratio in Direct-Injection Diesel Engines on NOx and Soot Emissions,” SAE Paper 961125.
5.
Espey, C., Pinson, J. A., and Litzinger, T. A., 1990, “Swirl Effects on Mixing and Flame Evolution in a Research DI Diesel Engine,” SAE Paper 902076.
6.
Fuchs, T. R., and Rutland, C. J., 1998, “Intake Flow Effects on Combustion and Emissions in a Diesel Engine,” SAE Paper 980508.
7.
Ladommatos, N., Balian, R. A., and Stone, R., 1992, “Analysis of Swirl in Unsteady Flow and its Effect on Diesel Combustion,” SAE Paper 921643.
8.
Gale, N. F., 1990, “Diesel Engine Cylinder Head Design: The Compromises and Techniques,” SAE Paper 900133.
9.
Monaghan, M. L., and Pettifer, H. F., 1981, “Air Motion and Its Effect on Diesel Performance and Emissions,” SAE Paper 810255.
10.
Tippelmann, G., 1977, “A New Method of Investigation of Swirl Ports,” SAE Paper 770404.
11.
Tindal, M. J., and Williams, T. J., 1977, “An Investigation of Cylinder Gas Motion in the Direct Injection Diesel Engine,” SAE Paper 770405.
12.
Snauwaert, P., and Sievens, R., 1986, “Experimental Study of the Swirl Motion in DI Diesel Engines Under Steady State Flow Conditions,” SAE Paper 860026.
13.
Zhu, Y., Evers, D., Huigen, G., and Hommersom, G., 1990, “LDA Measurements of Steady and Unsteady Flow through the Induction System of a Heavy Duty Diesel Engine,” SAE Paper 901576.
14.
Arcoumanis, C., and Tanabe, S., 1989, “Swirl Generation by Helical Ports,” SAE Paper 890790.
15.
Stier, B., and Falco, R., 1995, “An Investigation of Fluid Flow During Induction Stroke of a Water Analog Model of an IC Engine Employing LIPA,” SAE Paper 950726.
16.
Kent, J. C., Mikulec, A., Rlmal, L., Adamczyk, A. A., Mueller, S. R., Stein, R. A., and Warren, C. C., 1989, “Observations on the Effects of Intake-Generated Swirl and Tumble on Combustion Duration,” SAE Paper 982096.
17.
Uzkan, T., Borgnakke, C., and Morel, T., 1983, “Characterization of Flow Produced by a High-Swirl Inlet Port,” SAE Paper 830266.
18.
Khalighi, B., Haworth, D. C., and Huebler, M. S., 1994, “Multi-Dimensional Port and In-Cylinder Flow Calculations and Flow Visualization Study in an Internal Combustion Engine with Different Intake Configurations,” SAE Paper 941871.
19.
Khalighi, B., Tahry, S. H. E., Haworth, D. C., and Huebler, M. S., 1995, “Computational and Measurement of Flow and Combustion in a Four-Valve Engine with Intake Variations,” SAE Paper 950287.
20.
Arcoumanis, C., Hadjiapostolou, A., and Whitelaw, J. H., 1987, “Swirl Center Precession in Engine Flows,” SAE Paper 870370.
21.
Baker, P., Benjamin, S. F., Girgis, N. G., Newman, A. W., and Seeley, W. A., 1995, “Characterization of Barrel Swirl Motion Under Steady Flow Conditions,” SAE Paper 950729.
22.
Qi, G., Zhou, J., Liu, Z., and Chen, J., 1995, “The Study of an Optimum Method for Inlet Port Performance in a D.I. Diesel Engine,” SAE Paper 952056.
23.
Durao, D. F. G., Heitor, M. V., Whitelaw, J. H., and Witze, P. O., 1990, Combustion Flow Diagnostics, NATO ASI Series, Kluwer Academic, Boston, MA.
24.
Wigley, G., and Hawkins, M. G., 1978, “Three Dimensional Velocity Measurements by Laser Anemometry in a Diesel Engine Cylinder Under Steady State Inlet Flow Conditions,” SAE Paper 780060.
25.
Hessel, R. P., 1993, “Numerical Simulation of Valved Intake Port and In-Cylinder Flows Using KIVA3,” Ph.D. thesis, University of Wisconson-Madison.
Copyright © 2000
 by ASME
You do not currently have access to this content.