Homogeneous charge compression ignition (HCCI) combustion has the potential for high efficiency with very low levels of NOx and soot emissions. However, HCCI has thus far only been achievable in a laboratory setting due the lack of control over the start and rate of combustion and its narrow operating range. In the present work, direct water injection (WI) was investigated to solve the aforementioned limitations of HCCI. This new advanced combustion mode is called thermally stratified compression ignition (TSCI). A three-dimensional computational fluid dynamics (3D CFD) model was developed using CONVERGE CFD coupled with detailed chemical kinetics to gain a better understanding of the underlying phenomena of the water injection event in a homogeneous, low temperature combustion (LTC) strategy. The CFD model was first validated against previously collected experimental data. The model was then used to simulate TSCI combustion and the results indicate that injecting water into the combustion chamber decreases the overall unburned gas temperature and increases the level of thermal stratification prior to ignition. The increased thermal stratification results in a decreased rate of combustion, thereby providing control over its rate. The results show that the peak pressure and gross heat release rate (HRR) decrease by 37.8% and 83.2%, respectively, when 6.7 mg of water were injected per cycle at a pressure of 160 bar. Finally, different spray patterns were simulated to observe their effect on the level of thermal stratification prior to ignition. The results show that the symmetric patterns with more nozzle holes were generally more effective at increasing thermal stratification.
Skip Nav Destination
Article navigation
November 2018
Research-Article
Computational Fluid Dynamics Simulations of the Effect of Water Injection Characteristics on TSCI: A New, Load-Flexible, Advanced Combustion Concept
Mozhgan Rahimi Boldaji,
Mozhgan Rahimi Boldaji
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: mozhgan.rahimiboldaji@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: mozhgan.rahimiboldaji@stonybrook.edu
Search for other works by this author on:
Aimilios Sofianopoulos,
Aimilios Sofianopoulos
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: aimilios.sofianopoulos@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: aimilios.sofianopoulos@stonybrook.edu
Search for other works by this author on:
Sotirios Mamalis,
Sotirios Mamalis
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: sotirios.mamalis@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: sotirios.mamalis@stonybrook.edu
Search for other works by this author on:
Benjamin Lawler
Benjamin Lawler
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: benjamin.lawler@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: benjamin.lawler@stonybrook.edu
Search for other works by this author on:
Mozhgan Rahimi Boldaji
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: mozhgan.rahimiboldaji@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: mozhgan.rahimiboldaji@stonybrook.edu
Aimilios Sofianopoulos
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: aimilios.sofianopoulos@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: aimilios.sofianopoulos@stonybrook.edu
Sotirios Mamalis
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: sotirios.mamalis@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: sotirios.mamalis@stonybrook.edu
Benjamin Lawler
Department of Mechanical Engineering,
Stony Brook University,
Stony Brook, NY 11790
e-mail: benjamin.lawler@stonybrook.edu
Stony Brook University,
Stony Brook, NY 11790
e-mail: benjamin.lawler@stonybrook.edu
Contributed by the IC Engine Division of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received May 11, 2018; final manuscript received May 16, 2018; published online July 9, 2018. Editor: David Wisler.
J. Eng. Gas Turbines Power. Nov 2018, 140(11): 112807 (10 pages)
Published Online: July 9, 2018
Article history
Received:
May 11, 2018
Revised:
May 16, 2018
Citation
Boldaji, M. R., Sofianopoulos, A., Mamalis, S., and Lawler, B. (July 9, 2018). "Computational Fluid Dynamics Simulations of the Effect of Water Injection Characteristics on TSCI: A New, Load-Flexible, Advanced Combustion Concept." ASME. J. Eng. Gas Turbines Power. November 2018; 140(11): 112807. https://doi.org/10.1115/1.4040309
Download citation file:
Get Email Alerts
Cited By
Shape Optimization of an Industrial Aeroengine Combustor to reduce Thermoacoustic Instability
J. Eng. Gas Turbines Power
Dynamic Response of A Pivot-Mounted Squeeze Film Damper: Measurements and Predictions
J. Eng. Gas Turbines Power
Review of The Impact Of Hydrogen-Containing Fuels On Gas Turbine Hot-Section Materials
J. Eng. Gas Turbines Power
Effects of Lattice Orientation Angle On Tpms-Based Transpiration Cooling
J. Eng. Gas Turbines Power
Related Articles
Simulation of Combustion Recession After End-of-Injection at Diesel Engine Conditions
J. Eng. Gas Turbines Power (October,2017)
Modeling Mixture Formation in a Gasoline Direct Injection Engine
J. Appl. Mech (November,2006)
Homogeneous Charge Compression Ignition Engine: A Simulation Study on the Effects of Inhomogeneities
J. Eng. Gas Turbines Power (April,2003)
Cold-Start Computational Fluid Dynamics Simulation of Spark-Ignition Direct-Injection Engine
J. Eng. Gas Turbines Power (November,2018)
Related Proceedings Papers
Related Chapters
Internal and Near Nozzle Flow Simulations of Gasoline Multi-Hole Injector (ECN Spray G) with Transient Needle Motion
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Physiology of Human Power Generation
Design of Human Powered Vehicles
Lay-Up and Start-Up Practices
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration