1-20 of 42
Keywords: wetting
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Heat Mass Transfer. October 2021, 143(10): 101602.
Paper No: HT-21-1140
Published Online: September 8, 2021
... from a balance between surface tension and buoyancy forces. It reasonably predicts vapor bubble sizes for certain conditions [ 36 ] but performs poorly for more well-wetting surfaces [ 37 ]. Additionally, a major limitation of Eq. (2) is that it does not account for the orifice size, and hence...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Heat Mass Transfer. February 2021, 143(2): 021604.
Paper No: HT-20-1300
Published Online: December 21, 2020
.... 654 – 678 . 10.1016/j.rser.2016.08.036 [8] Sefiane , K. , and Bennacer , R. , 2009 , “ Nanofluids Droplets Evaporation Kinetics and Wetting Dynamics on Rough Heated Substrates ,” Adv. Colloid Interface Sci. , 147–148 , pp. 263 – 271 . 10.1016/j.cis.2008.09.011 [9...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Heat Mass Transfer. April 2012, 134(4): 041202.
Published Online: February 15, 2012
... 09 2011 15 02 2012 15 02 2012 chemically reactive flow flames flow simulation fuel organic compounds two-phase flow wetting concurrent flame spread methanol pool liquid–gas interface flame spread velocity flame anchoring point The following assumptions...
Journal Articles
Publisher: ASME
Article Type: Heat Transfer In Nanochannels, Microchannels, And Minichannels
J. Heat Mass Transfer. February 2012, 134(2): 020901.
Published Online: December 13, 2011
.... Contact angles were measured on this backup surface [( 13 )]. The SiOx surface shows a relatively high wettability; whereas the SiOC surface is an unwetted (hydrophobic) surface. The Ti and diamond-like carbon (DLC) surfaces are both wetted (hydrophilic) and have static contact angles ( θ) of 49° and 63...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Review Articles
J. Heat Mass Transfer. November 2011, 133(11): 110801.
Published Online: September 2, 2011
... 02 09 2011 boiling drops heat transfer jets microchannel flow sprays two-phase flow wetting high heat flux extreme-high heat flxu jet impingement spray microchannel piezoelectric droplet wettability electronic cooling thermal management According...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Photo Gallery
J. Heat Mass Transfer. August 2011, 133(8): 080905.
Published Online: April 27, 2011
...Jae Bong Lee; Seong Hyuk Lee; Chang Kyoung Choi aluminium contact angle drops flow visualisation high-speed optical techniques hole density hydrophobicity impact (mechanical) microfluidics milling machines surface energy surface roughness surface texture water wetting 27...
Journal Articles
Publisher: ASME
Article Type: Photo Gallery
J. Heat Mass Transfer. August 2011, 133(8): 080904.
Published Online: April 27, 2011
...Yulong Ji; Hsiu-hung Chen; Qingsong Yu; Xuehu Ma; H. B. Ma 27 04 2011 27 04 2011 coatings contact angle cooling copper hydrophobicity monolayers organic compounds self-assembly wetting 2011 American Society of Mechanical Engineers ...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Heat Mass Transfer. September 2010, 132(9): 094503.
Published Online: July 15, 2010
... condensation form is still not clear. We suggest a condensation model based on droplet nucleation and growth on elevated precipitates, resulting in short-term steam entrapment after droplet coalescence. According to the wetting theory, this transition state yields increased macroscopic contact angles...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Heat Mass Transfer. September 2010, 132(9): 091201.
Published Online: June 28, 2010
... external flows flames flow simulation heat radiation numerical analysis wetting 07 10 2009 19 04 2010 28 06 2010 28 06 2010 Fernandez-Pello , A. C. , 1978 , “ A Theoretical Model for the Upward Laminar Spread of Flames Over Vertical Fuel Surfaces ,” Combust...
Journal Articles
Publisher: ASME
Article Type: Photo Gallery
J. Heat Mass Transfer. August 2010, 132(8): 080904.
Published Online: June 11, 2010
...C. Dietz; K. Rykaczewski; A. Fedorov; Y. Joshi condensation contact angle copper compounds drops heat transfer hydrophobicity nanostructured materials scanning electron microscopy wetting 11 06 2010 11 06 2010 2010 American Society of Mechanical Engineers ...
Journal Articles
Publisher: ASME
Article Type: Photo Gallery
J. Heat Mass Transfer. August 2010, 132(8): 080905.
Published Online: June 11, 2010
...Dong Hwan Shin; Seong Hyuk Lee; Scott Retterer; Chang Kyoung Choi 11 06 2010 11 06 2010 contact angle drops evaporation flow visualisation hydrophobicity two-phase flow water wetting 2010 American Society of Mechanical Engineers ...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Heat Mass Transfer. June 2010, 132(6): 061501.
Published Online: March 25, 2010
... magnitude of CHF enhancement in pure water as for nanofluids. Subsequent to the boiling experiments, the interfacial properties of the heater surfaces were examined using dynamic wetting of an evaporating water droplet. As the surface temperature increased, the evaporating meniscus on the clean surface...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Heat Mass Transfer. December 2009, 131(12): 121004.
Published Online: October 15, 2009
... surfaces with enhanced boiling heat transfer performance and novel phase-change based micro-actuators and energy harvesters. 28 09 2007 28 03 2008 15 10 2009 bubbles cavitation flow simulation hydrophobicity wetting single bubble hydrophobic surface nucleate boiling...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Micro/Nanoscale Heat Transfer—Part I
J. Heat Mass Transfer. March 2009, 131(3): 033101.
Published Online: January 13, 2009
... the disjoining pressure concept. The perfectly wetting case is described using the usual h − 3 disjoining pressure. The partially wetting case is modeled using the integrated 6–12 Lennard-Jones potential. The developed model is used for investigating the effects of the surface topography, gravity...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Heat Mass Transfer. December 2008, 130(12): 121701.
Published Online: September 16, 2008
... 04 2008 16 09 2008 differential equations flow through porous media heat transfer magnetohydrodynamics rotational flow transforms viscosity wetting three-dimensional flow heat transfer MHD homotopy analysis method analytic solution In recent years the study...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Heat Mass Transfer. February 2008, 130(2): 024504.
Published Online: February 15, 2008
...S. K. Sahu; P. K. Das; S. Bhattacharyya The effect of precursory cooling on conduction-controlled rewetting of both slab and solid cylinder is analyzed by the heat balance integral method. A constant heat transfer coefficient is assumed in the wet region behind the wet front, while an exponentially...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Heat Mass Transfer. November 2007, 129(11): 1476–1485.
Published Online: March 18, 2007
... of the adsorbed film, the heat flux, the spreading characteristics of an almost pure fluid, and, therefore, the assumptions in modeling. The understanding of the details of interfacial phenomena in the extended contact line region (thickness, δ < 3 μ m ) of an evaporating completely wetting...