In this paper, a predictive thermal and analytical modeling approach for orthogonal cutting process is introduced to conveniently calculate forces, stress, and temperature distributions. The modeling approach is based on the work material constitutive model, which depends on strain, strain rate, and temperature. In thermal modeling, oblique moving band heat source theory is utilized and analytically combined with modified Oxley’s parallel shear zone theory. Normal stress distribution on the tool rake face is modeled as nonuniform with a power-law relationship. Hence, nonuniform heat intensity at the tool-chip interface is obtained from the predicted stress distributions utilizing slip line field analysis of the modified secondary shear zone. Heat sources from shearing in the primary zone and friction at the tool-chip interface are combined, heat partition ratios are determined for temperature equilibrium to obtain temperature distributions depending on cutting conditions. Model validation is performed by comparing some experimental results with the predictions for machining of AISI 1045 steel, AL 6082-T6, and AL 6061-T6 aluminum. Close agreements with the experiments are observed. A set of detailed, analytically computed stress and temperature distributions is presented.
Skip Nav Destination
e-mail: ozel@rci.rutgers.edu
Article navigation
Technical Papers
Predictive Analytical and Thermal Modeling of Orthogonal Cutting Process—Part I: Predictions of Tool Forces, Stresses, and Temperature Distributions
Yiğit Karpat,
Yiğit Karpat
Department of Industrial and Systems Engineering,
Rutgers University
, Piscataway, NJ 08854
Search for other works by this author on:
Tuğrul Özel
Tuğrul Özel
Department of Industrial and Systems Engineering,
e-mail: ozel@rci.rutgers.edu
Rutgers University
, Piscataway, NJ 08854
Search for other works by this author on:
Yiğit Karpat
Department of Industrial and Systems Engineering,
Rutgers University
, Piscataway, NJ 08854
Tuğrul Özel
Department of Industrial and Systems Engineering,
Rutgers University
, Piscataway, NJ 08854e-mail: ozel@rci.rutgers.edu
J. Manuf. Sci. Eng. May 2006, 128(2): 435-444 (10 pages)
Published Online: September 16, 2005
Article history
Received:
May 19, 2005
Revised:
September 16, 2005
Connected Content
Citation
Karpat, Y., and Özel, T. (September 16, 2005). "Predictive Analytical and Thermal Modeling of Orthogonal Cutting Process—Part I: Predictions of Tool Forces, Stresses, and Temperature Distributions." ASME. J. Manuf. Sci. Eng. May 2006; 128(2): 435–444. https://doi.org/10.1115/1.2162590
Download citation file:
Get Email Alerts
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
Related Articles
Predictive Analytical and Thermal Modeling of Orthogonal Cutting Process—Part II: Effect of Tool Flank Wear on Tool Forces, Stresses, and Temperature Distributions
J. Manuf. Sci. Eng (May,2006)
Analytical and Thermal Modeling of High-Speed Machining With Chamfered Tools
J. Manuf. Sci. Eng (February,2008)
Identification of a Friction Model at the Tool-Chip-Workpiece Interface in Dry Machining of a AISI 1045 Steel With a TiN Coated Carbide Tool
J. Tribol (October,2011)
Thermo-Viscoplastic Modeling of Machining Process Using a Mixed Finite Element Method
J. Manuf. Sci. Eng (November,1996)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
A 3D Cohesive Modelling Approach for Hydrogen Embrittlement in Welded Joints of X70 Pipeline Steel
International Hydrogen Conference (IHC 2012): Hydrogen-Materials Interactions
Development of the Cost-Efficient Steel 18MnCrMoV4-8-7 for Case-Hardening or Carbonitriding of Mid-Sized Roller Bearings
Bearing and Transmission Steels Technology