Lightweight metal–matrix nanocomposites (MMNCs) (metal matrix with nanosized ceramic particles) can be of significance for automobile, aerospace, and numerous other applications. It would be advantageous to develop effective nanomanufacturing methods for fabrication of bulk components of aluminum based MMNCs through solidification processing. However, it is extremely difficult to disperse nanosized ceramic particles uniformly in molten aluminum. In this paper, a high power ultrasonic probe is used to disperse nanosized SiC particles into molten aluminum alloy A356. Experimental results show that the ultrasonic cavitation based dispersion of nanoparticles in molten aluminum alloy is effective. The uniform nanoparticle dispersion in the Al alloy matrix resulted in significantly improved mechanical properties. To enhance the nanomanufacturing efficiency, various nanoparticle feeding techniques were explored and experimental results are presented.
Skip Nav Destination
e-mail: xcli@cae.wisc.edu
Article navigation
June 2007
Technical Papers
Ultrasonic Cavitation Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites
Yong Yang,
Yong Yang
Department of Mechanical Engineering,
University of Wisconsin-Madison
, 1513 University Avenue, Madison WI 53706
Search for other works by this author on:
Xiaochun Li
Xiaochun Li
Department of Mechanical Engineering,
e-mail: xcli@cae.wisc.edu
University of Wisconsin-Madison
, 1513 University Avenue, Madison WI 53706
Search for other works by this author on:
Yong Yang
Department of Mechanical Engineering,
University of Wisconsin-Madison
, 1513 University Avenue, Madison WI 53706
Xiaochun Li
Department of Mechanical Engineering,
University of Wisconsin-Madison
, 1513 University Avenue, Madison WI 53706e-mail: xcli@cae.wisc.edu
J. Manuf. Sci. Eng. Jun 2007, 129(3): 497-501 (5 pages)
Published Online: February 5, 2006
Article history
Received:
September 27, 2005
Revised:
February 5, 2006
Citation
Yang, Y., and Li, X. (February 5, 2006). "Ultrasonic Cavitation Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites." ASME. J. Manuf. Sci. Eng. June 2007; 129(3): 497–501. https://doi.org/10.1115/1.2714583
Download citation file:
Get Email Alerts
Special Section: Manufacturing Science Engineering Conference 2024
J. Manuf. Sci. Eng (November 2024)
Anisotropy in Chip Formation in Orthogonal Cutting of Rolled Ti-6Al-4V
J. Manuf. Sci. Eng (January 2025)
Modeling and Experimental Investigation of Surface Generation in Diamond Micro-Chiseling
J. Manuf. Sci. Eng (February 2025)
Estimation of Temperature Rise in Magnetorheological Fluid-Based Finishing of Thin Substrate: A Theoretical and Experimental Study
J. Manuf. Sci. Eng (February 2025)
Related Articles
Ultrasonic Cavitation-Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites
J. Manuf. Sci. Eng (April,2007)
Mechanical Properties and Microstructure of Mg ∕ Si C Nanocomposites Fabricated by Ultrasonic Cavitation Based Nanomanufacturing
J. Manuf. Sci. Eng (June,2008)
Fraction Solid Measurements on Solidifying Melt
J. Fluids Eng (March,2004)
A Micromechanics-Based Elastoplastic Model for Amorphous Composites With Nanoparticle Interactions
J. Appl. Mech (May,2008)
Related Proceedings Papers
Related Chapters
Chitosan-Based Drug Delivery Systems
Chitosan and Its Derivatives as Promising Drug Delivery Carriers
Rubber Nanocomposites for a Representative Volume Element with Hyperelastic and Elastic Matrix
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Preparation and Thermal Property of Phase Change Nanocomposites Using Carbon Nanotubes as Additives
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)