The microstructure-level finite element machining model developed in Part I of this paper is used to perform a detailed analysis of the failure mechanisms that occur while machining the carbon nanotube (CNT) reinforced polycarbonate composites. The chip formation in plain polycarbonate (PC) is seen to be influenced by the ductile failure mode. For the composite containing 1.75% by weight of CNTs (Composite A), the polymer fails in the ductile mode. The presence of CNTs is seen to result in CNTs protruding from the machined surface and subsurface damage. The low thermal conductivity of the polymer phase is seen to result in the formation of adiabatic shear bands in plain PC and Composite A. As the CNT loading is increased to 5% by weight, the failure in the polymer phase is seen to be predominantly brittle in nature. The presence of the larger percentage of CNTs is also seen to offset the formation of adiabatic shear bands. The machining model has also been used to successfully predict the machining behavior of CNT composites with tailored microstructures. Simulation experiments with varying CNT alignment, aspect ratio, percentage loading, and cutting velocity were conducted to study the effects of these factors on cutting forces. The results show that the machining model in combination with the material model is an effective tool to design CNT composites with emphasis both on the mechanical properties and machinability.
Skip Nav Destination
Article navigation
June 2008
Special Section: Micromanufacturing
Microstructure-Level Machining Simulation of Carbon Nanotube Reinforced Polymer Composites—Part II: Model Interpretation and Application
A. Dikshit,
A. Dikshit
Graduate Research Assistant
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
Search for other works by this author on:
J. Samuel,
J. Samuel
Graduate Research Assistant
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
Search for other works by this author on:
R. E. DeVor,
R. E. DeVor
Professor
Fellow ASME
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
Search for other works by this author on:
S. G. Kapoor
S. G. Kapoor
Professor
Fellow ASME
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
Search for other works by this author on:
A. Dikshit
Graduate Research Assistant
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
J. Samuel
Graduate Research Assistant
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
R. E. DeVor
Professor
Fellow ASME
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801
S. G. Kapoor
Professor
Fellow ASME
Department of Mechanical Science and Engineering,
University of Illinois at Urbana-Champaign
, Urbana, IL 61801J. Manuf. Sci. Eng. Jun 2008, 130(3): 031115 (8 pages)
Published Online: May 23, 2008
Article history
Received:
November 14, 2007
Revised:
January 16, 2008
Published:
May 23, 2008
Connected Content
A companion article has been published:
Microstructure-Level Machining Simulation of Carbon Nanotube Reinforced Polymer Composites—Part I: Model Development and Validation
Citation
Dikshit, A., Samuel, J., DeVor, R. E., and Kapoor, S. G. (May 23, 2008). "Microstructure-Level Machining Simulation of Carbon Nanotube Reinforced Polymer Composites—Part II: Model Interpretation and Application." ASME. J. Manuf. Sci. Eng. June 2008; 130(3): 031115. https://doi.org/10.1115/1.2927431
Download citation file:
Get Email Alerts
Related Articles
A Microstructure-Level Material Model for Simulating the Machining of Carbon Nanotube Reinforced Polymer Composites
J. Manuf. Sci. Eng (June,2008)
Experimental Investigation of the Machinability of Polycarbonate Reinforced With Multiwalled Carbon Nanotubes
J. Manuf. Sci. Eng (May,2006)
Related Chapters
Layer Arrangement Impact on the Electromechanical Performance of a Five-Layer Multifunctional Smart Sandwich Plate
Advanced Multifunctional Lightweight Aerostructures: Design, Development, and Implementation
Modeling of Cutting Force in Vibration-Assisted Machining
Vibration Assisted Machining: Theory, Modelling and Applications
Cutting and Machining
Fabrication of Metallic Pressure Vessels