The main objective of this paper is to simulate springback using a combined kinematic/isotropic hardening model. Material parameters in the hardening model are identified by an inverse method. A three-point bending test is conducted on 6022-T4 aluminum sheet. Punch stroke, punch load, bending strain, and bending angle are measured directly during the tests. Bending moments are then computed from these measured data. Bending moments are also calculated based on a constitutive model. Material parameters are identified by minimizing the normalized error between two bending moments. A micro genetic algorithm is used in the optimization procedure. Stress-strain curves are generated with the material parameters found in this way, which can be used with other plasticity models. ABAQUS/Standard, which has the combined isotropic/kinematic hardening model, is used to simulate draw-bend of 6022-T4 aluminum sheet. Absolute springback angles are predicted very accurately.
Issue Section:
Technical Papers
1.
Zhang
, Z. T.
, and Hu
, S. J.
, 1998
, “Stress and Residual Stress Distributions in Plane Strain Bending
,” Int. J. Mech. Sci.
, 40
, No. 6
, pp. 533
–543
.2.
Wenner
, M. L.
, 1983
, “On Work Hardening and Springback in Plane Strain Draw Forming
,” Journal Applied Metal Working
, 2
, No. 4
, pp. 342
–349
.3.
Mickalich, M. K., and Wenner, M. L., 1998, “Calculation of Springback and its Variation in Channel Forming Operations,” Symposium Proceedings, Society of Automotive Engineers Meeting, Detroit, pp. 125–131.
4.
Zhang, and Lee, D., 1995, “Effect of Process Variables and Material Properties on the Springback Behavior of 2-D Draw Bending Parts,” SAE Technical Paper Series 950692, International Congress and Exposition, MI.
5.
Tang, S. C., 1987, “Analysis of Springback in Sheet Forming Operation,” Proceedings of ICTP, Advanced Technology of Plasticity, pp. 193–197.
6.
Tang, S. C., 1990, “An Anisotropic Hardening Rule for the Analysis of Sheet Forming Operations,” Proceedings of ICTP, Advanced Technology of Plasticity, pp. 1149–1154.
7.
Tang, S. C., 1996, “Application of an Anisotropic Hardening Rule to Springback Prediction,” Proceedings of ICTP, Advanced Technology of Plasticity, pp. 719–722.
8.
Kuwabara, T., Morita, Y., Miyashita, Y. and Takahashi, S., 1995, “Elastic-Plastic Behavior of Sheet Metal Subjected to In-plane Reverse Loading,” Proceedings of Plascity ’95: Dynamic Plasticity and Structural Behaviors, Gordon and Breach Publishers, pp. 841–844.
9.
Li, K. and Wagoner, R. H., 1998, “Simulation of Springback,” Simulation of Materials Processing: Theory, Methods and Applications, NUMIFORM’98, Huetink and Baaijens, eds., Enschede, The Netherlands, pp. 21–31.
10.
Hu, Y., 1999, “A Few Issues on Accuracy of Springback Simulation of Automobile Parts,” SAE Technical Paper Series 1999-01-1000, International Congress and Exposition, MI.
11.
Shi, M. F., and Zhang, L., 1999, “Issues Concerning Material Constitutive Laws and Parameters in Springback Simulations,” SAE Technical Paper Series 1999-01-1002, International Congress and Exposition, MI.
12.
Geng, L., and Wanoger, R. H., 2000, “Springback Analysis with a Modified Hardening Mode,” SAE Technical Paper Series 2000-01-0768, World Congress, MI.
13.
Jiang, S., Garnett, M., and Liu, S.-D., 2000, “Springback of Sheet Metal Subjected to Multiple Bending-Unbending Cycles,” SAE Technical Paper Series 2000-01-1112, World Congress, MI.
14.
Anon, 1998, “Models for Metals Subjected to Cyclic Loading,” ABAQUS Theory Manual, Hibbitt, Karlsson & and Sorensen, Version 5.8, pp. 4.3.5.1–4.3.5.4
15.
Sidoroff
, F.
, 1975
, “On the Formulation of Plasticity and Viscoplasticity with Internal Variables
,” Arch. Mech.
, 27
, No. 5–6
, pp. 807
–819
.16.
Chaboche
, J. L.
, and Rousselier
, G.
, 1983
, “On the Plastic and Viscoplastic Constitutive Equations—Part 1: Rules Developed with Internal Variable Concept
,” ASME J. Pressure Vessel Technol.
, 105
, pp. 153
–158
.17.
Lemaitre, J., and Chaboche, J.-L., 1990, Mechanics of Solid Materials, Cambridge University Press, pp. 161–241.
18.
Lee
, D.
, and Zaverl
, F.
, Jr., 1979
, “A Description of History Dependent Plastic Flow Anisotropic Metals
,” ASME J. Eng. Mater. Technol.
, 101
, pp. 59
–67
.19.
Brunet, M., Morestin, F., and Godereaux, S., 2000, “Non-Linear Kinematic Hardening Identification for Anisotropic Sheet-Metals with Bending-Unbending Tests,” MED-Vol. 11, Proceedings of the ASME Manufacturing in Engineering Division, ASME 2000, pp. 599–604.
20.
Hill
, R.
, 1979
, “Theoretical Plasticity of Textured Aggregates
,” Math. Proc. Cambridge Philos. Soc.
, 85
, pp. 179
–191
.21.
Zhao, K. M., and Lee, J. K., 2000, “Generation of Cyclic Stress-Strain Curves for Sheet Metals,” MED-Vol. 11, Proceedings of the ASME Manufacturing in Engineering Division, ASME 2000, pp. 667–674.
22.
Hosford
, W. F.
, 1985
, “Comments on Anisotropic Yield Criteria
,” Int. J. Mech. Sci.
, 27
, pp. 423
–27
.23.
Morestin
, F.
, and Boivin
, M.
, 1996
, “On the Necessity of Taking into Account the Variation in the Young Modulus with Plastic Strain in Elastic—Plastic Software
,” Nucl. Eng. Des.
, 162
, pp. 107
–116
.24.
Goldberg, D. E., 1989, Genetic Algorithms in Search, Optimization, and Machine Learning, Addison-Wesley, NY.
25.
Davis, L., 1991, Handbook of Genetic Algorithms, Von Nostrand Reinhold, New York.
26.
Amadieu, O., and Parisot, C., 1997, “Advanced Genetic Algorithms in Fortran 90,” www.essi.fr/∼parisot/ga200/ga.html.
27.
Vallance
, D. W.
, and Matlock
, D. K.
, 1992
, “Application of the Bending-Under-Tension Friction Test to Coated Sheet Steels
,” J. Mater. Eng. Perform.
, 1
, No. 5
, pp. 685
–693
.28.
Wenzloff
, G. J.
, Hylton
, C. H.
, and Matlock
, D. K.
, 1992
, “A New Procedure for the Bending Under Tension Friction Test
,” J. Mater. Eng. Perform.
, 1
, No. 5
, pp. 609
–613
.29.
Wagoner, R. H., Carden, W. D., Carden, W. P., and Matlock, K., 1997, “Springback after Drawing and Bending of Metal Sheets,” THERMEC’97, Australia.
Copyright © 2001
by ASME
You do not currently have access to this content.
