A general approach for designing interference-fit joints constituted of elastic-plastic components is presented. The wide applicability range of the method was achieved removing restrictive assumptions about material characterization and yield criterion, which were included in previous theoretical models. Because of the general approach, the model is solved with an iterative procedure. The theory has been successfully validated by a result comparison with finite element models.
Issue Section:
Technical Papers
1.
Gamer
, U.
, 1986
, “The Rotating Elastic-Plastic Shrink Fit with Hardening
,” Acta Mech.
, 61
(1–4
), pp. 15
–27
.2.
Gamer
, U.
, 1986
, “The Plastic-Plastic Shrink Fit with Supercritical Interference
,” Acta Mech.
, 61
(1–4
), pp. 1
–14
.3.
Gamer
, U.
, 1987
, “The Shrink Fit with Elastic-Plastic Hub Exhibiting Constant Yield Stress Followed by Hardening
,” International Journal of Solids and Structures
, 23
(9
), pp. 1219
–1224
.4.
Gamer
, U.
, 1987
, “The Shrink Fit with Nonlinearly Hardening Elastic-Plastic Hub
,” ASME J. Appl. Mech.
, 54
(2
), pp. 474
–476
.5.
Gamer
, U.
, 1989
, “The Effect of a Special Hardening Law on Continuity in Elastic-Plastic Problems with Rotational Simmetry
,” Forsch. Geb. Ingenieurwes.
, 55
(2
), pp. 60
–64
.6.
Gamer
, U.
, 1990
, “Der elastisch-plastische Querpreßverband bei verschiedenen Flie§grenzen von Innen- und Außenteil
,” Forsch. Geb. Ingenieurwes.
, 56
(5
), pp. 166
–168
.7.
Gamer
, U.
, 1992
, “A Concise Treatment of the Shrink Fit with Elastic-Plastic Hub
,” International Journal of Solids and Structures
, 29
(20
), pp. 2463
–2469
.8.
Gamer
, U.
, and Orc¸an
, Y.
, 1990
, “The Shrink Fit Consisting of Elastic Hollow Shaft and Nonlinearly Hardening Elastic-Plastic Hub
,” Acta Mech.
, 81
(1–2
), pp. 97
–108
.9.
Megahed
, M. M.
, and Abdel-Kader
, M. S.
, 1993
, “Elastic-Plastic Analysis of Rotating Shrink-Fitted Discs with Nonlinear Hardening Characteristics
,” International Jounral of Solids and Structures
, 30
(6
), pp. 751
–765
.10.
Guven
, U.
, 1991
, “The Shrink Fit with Elastic-Plastic Hub Exhibiting Variable Thickness
,” Eng. Comput.
, 61
(1–4
), pp. 65
–72
.11.
Guven
, U.
, 1993
, “Stress Distribution in Shrink Fit with Elastic-Plastic Hub Exhibiting Variable Thickness
,” Int. J. Mech. Sci.
, 35
(1
), pp. 39
–46
.12.
Mack
, W.
, 1993
, “Thermal Assembly of an Elastic-Plastic Hub and a Solid Shaft
,” Archive of Applied Mechanics
, 63
(1
), pp. 42
–50
.13.
Mack
, W.
, and Bengeri
, M.
, 1994
, “Thermal Assembly of an Elastic-Plastic Shrink Fit with Solid Inclusion
,” Int. J. Mech. Sci.
, 36
(8
), pp. 699
–705
.14.
Lytkina
, N. A.
, et al., 1987
, “Calculation of Joint Stresses in Interference-fit Shaft-mounted Gears
,” Soviet Engineering Research
, 7
(5
), pp. 27
–30
.15.
Tyutikov
, G. F.
, 1987
, “Cylindrical Joints with Large Interference
,” Soviet Engineering Research
, 7
(12
), pp. 8
–12
.16.
Millenson, M. B., and Manson, S. S., 1948, “Determination of Stresses in Gas Turbine Disks Subjected to Plastic Flow and Creep,” NACA Report # 906.
17.
Taylor
, G. I.
, and Quinney
, I.
, 1932
, “The Plastic Distortion of Metals
,” Philos. Trans. R. Soc. London, Ser. A
, 230
, pp. 323
–362
.Copyright © 2004
by ASME
You do not currently have access to this content.