Carbon nanotube (CNT)-based piezoresistive strain sensors have the potential to outperform traditional silicon-based piezoresistors in MEMS devices due to their high strain sensitivity. However, the resolution of CNT-based piezoresistive sensors is currently limited by excessive 1/f or flicker noise. In this paper, we will demonstrate several nanomanufacturing methods that can be used to decrease noise in the CNT-based sensor system without reducing the sensor's strain sensitivity. First, the CNTs were placed in a parallel resistor network to increase the total number of charge carriers in the sensor system. By carefully selecting the types of CNTs used in the sensor system and by correctly designing the system, it is possible to reduce the noise in the sensor system without reducing sensitivity. The CNTs were also coated with aluminum oxide to help protect the CNTs from environmental effects. Finally, the CNTs were annealed to improve contact resistance and to remove adsorbates from the CNT sidewall. The optimal annealing conditions were determined using a design-of-experiments (DOE). Overall, using these noise mitigation techniques it is possible to reduce the total noise in the sensor system by almost 3 orders of magnitude and increase the dynamic range of the sensors by 48 dB.
Skip Nav Destination
e-mail: culpepper@mit.edu
Article navigation
March 2013
This article was originally published in
Journal of Micro and Nano-Manufacturing
Research-Article
Nanomanufacturing Methods for the Reduction of Noise in Carbon Nanotube-Based Piezoresistive Sensor Systems
Michael A. Cullinan,
Michael A. Cullinan
Massachusetts Institute of Technology
,Department of Mechanical Engineering
,Cambridge, MA 021391
;National Institute of Standards and Technology
,Intelligent Systems Division
,Gaithersburg, MD 20899
Search for other works by this author on:
Martin L. Culpepper
e-mail: culpepper@mit.edu
Martin L. Culpepper
1
Massachusetts Institute of Technology
,Department of Mechanical Engineering
,Cambridge, MA 021391
e-mail: culpepper@mit.edu
1Corresponding author.
Search for other works by this author on:
Michael A. Cullinan
Massachusetts Institute of Technology
,Department of Mechanical Engineering
,Cambridge, MA 021391
;National Institute of Standards and Technology
,Intelligent Systems Division
,Gaithersburg, MD 20899
Martin L. Culpepper
Massachusetts Institute of Technology
,Department of Mechanical Engineering
,Cambridge, MA 021391
e-mail: culpepper@mit.edu
1Corresponding author.
Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF Micro AND Nano-Manufacturing. Manuscript received January 8, 2012; final manuscript received August 22, 2012; published online March 22, 2013. Assoc. Editor: Liwei Lin.
J. Micro Nano-Manuf. Mar 2013, 1(1): 011011 (6 pages)
Published Online: March 22, 2013
Article history
Received:
January 8, 2012
Revision Received:
August 22, 2012
Citation
Cullinan, M. A., and Culpepper, M. L. (March 22, 2013). "Nanomanufacturing Methods for the Reduction of Noise in Carbon Nanotube-Based Piezoresistive Sensor Systems." ASME. J. Micro Nano-Manuf. March 2013; 1(1): 011011. https://doi.org/10.1115/1.4023159
Download citation file:
62
Views
Get Email Alerts
Cited By
Investigation of Virtual Impactor Design Parameters in Aerosol Jet Printing Using Computational Fluid Dynamics
J. Micro Nano Sci. Eng (September 2025)
An Experimental Study on Material Removal Mechanisms in Quasi-Continuous Wave Fiber Laser Microdrilling of SS 304
J. Micro Nano Sci. Eng (June 2025)
Related Articles
Electrical Contact Resistance at the Carbon Nanotube/Pd and Carbon Nanotube/Al Interfaces in End-Contact by First-Principles Calculations
J. Electron. Packag (June,2011)
Fabrication of Six Degrees-of-Freedom Hexflex Positioner With Integrated Strain Sensing Using Nonlithographically Based Microfabrication
J. Micro Nano-Manuf (March,2021)
Frequency Shifts of Micro and Nano Cantilever Beam Resonators Due to Added Masses
J. Dyn. Sys., Meas., Control (September,2016)
Design and Test of Carbon Nanotube Biwick Structure for High-Heat-Flux Phase Change Heat Transfer
J. Heat Transfer (May,2010)
Related Proceedings Papers
Related Chapters
A CNT/Metal Hybrid Routing Architecture to Improve Performance of Ultra-Large FPGAs
International Conference on Software Technology and Engineering, 3rd (ICSTE 2011)
Tensile Behavior of CNT-CF/PP Composite Obtained from Experimental and Numerical Modeling Methods
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)
Calculation of Elastic Properties of PMMA/CNT Using Molecular Dynamics Simulations
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)